Effect of Coconut Milk, Cow Milk, and Soybean Oil on the Surface Roughness of Milled (PICN, RNC) and 3D-Printed Hybrid Resin–Ceramic: An In Vitro Study
Polymers · 10.03.2026 · 18 (6) · 670
DOI: 10.3390/polym18060670 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 10.03.2026. Verfasst von Seelassaya Leelaponglit und 3 weiteren Autor:innen. Beteiligte Einrichtung: Division of Restorative and Esthetic Dentistry, Faculty of Dentistry, Thammasat University, Pathum Thani 12120, Thailand. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 29 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Faculty of Dentistry Thammasat University Re-search Fund,, Faculty of Dentistry Thammasat University Research Fund.
Abstract (Originalsprache)
This in vitro study assessed the impact of coconut milk, cow milk, and soybean oil on the surface roughness (Ra) of two milled (polymer-infiltrated ceramic network (PICN), Vita Enamic (EN) and resin nanoceramic (RNC), Cerasmart (CS)) and 3D-printed (VarseoSmile Crown plus (VS)) hybrid resin–ceramic materials. Standardized rectangular specimens were prepared and subjected to cyclic immersion in the test media at 37 °C for 30 days to simulate dietary exposure. Surface roughness was measured pre- and post-aging, and statistical analysis was performed using two-way ANOVA and paired t-tests (α = 0.05). All media significantly increased Ra across all materials (p < 0.001). While coconut milk and soybean oil caused comparable roughening (Ra up to 0.155 µm), cow milk exhibited a material-specific impact. It roughened milled materials (EN and CS) (Ra: 0.147–0.154 µm) significantly more than the 3D-printed material (VS) (Ra: 0.126 µm) (p < 0.05). Notably, all post-aging Ra values remained below the clinical bacterial adhesion threshold of 0.2 µm. In conclusion, while all tested dietary media significantly degraded the surface topography of hybrid resin–ceramics, the 3D-printed hybrid resin–ceramic material demonstrated superior resistance to cow milk compared to milled alternatives. Nonetheless, plaque retention risks remain clinically acceptable for all tested materials.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Division of Restorative and Esthetic Dentistry, Faculty of Dentistry, Thammasat University, Pathum Thani 12120, Thailand.
ORCID-Profile: Awiruth Klaisiri
Förderung
- Faculty of Dentistry Thammasat University Re-search Fund,
- Faculty of Dentistry Thammasat University Research Fund
Zitieren
APA
Leelaponglit, S., Klaisiri, A., Angkananuwat, C., & Krajangta, N. (2026). Effect of Coconut Milk, Cow Milk, and Soybean Oil on the Surface Roughness of Milled (PICN, RNC) and 3D-Printed Hybrid Resin–Ceramic: An In Vitro Study. Polymers, 18(6), 670. https://doi.org/10.3390/polym18060670
Vancouver
Leelaponglit S, Klaisiri A, Angkananuwat C, Krajangta N. Effect of Coconut Milk, Cow Milk, and Soybean Oil on the Surface Roughness of Milled (PICN, RNC) and 3D-Printed Hybrid Resin–Ceramic: An In Vitro Study. Polymers. 2026;18(6):670. doi:10.3390/polym18060670
BibTeX
@article{Leelaponglit2026,
author = {Leelaponglit, Seelassaya and Klaisiri, Awiruth and Angkananuwat, Chayanit and Krajangta, Nantawan},
title = {Effect of Coconut Milk, Cow Milk, and Soybean Oil on the Surface Roughness of Milled (PICN, RNC) and 3D-Printed Hybrid Resin–Ceramic: An In Vitro Study},
journal = {Polymers},
year = {2026},
volume = {18},
number = {6},
pages = {670},
doi = {10.3390/polym18060670}
}
EUVIMED