EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Surface Characteristics and Hydrolytic Stability in Milled and 3D-Printed PMMA Dental Materials

Liliana Porojan iD, Flavia Roxana Bejan iD, Roxana Diana Vasiliu, Mihaela Ionela Gherban iD, Lavinia Cristina Moleriu, Anamaria Matichescu iD

Polymers · 28.02.2026 · 18 (5) · 597

DOI: 10.3390/polym18050597 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 28.02.2026. Verfasst von Liliana Porojan und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Dental Prostheses Technology (Dental Technology), Center for Advanced Technologies in Dental Prosthodontics, Faculty of Dental Medicine…. Die Arbeit nennt 42 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study investigated how fabrication method (milling versus 3D printing) affects the water sorption and solubility of PMMA dental materials, and how surface characteristics affect hydrolytic stability. Fifty-six PMMA samples were divided into three groups fabricated from CAD/CAM milled discs (Group A: I–III) and four groups from 3D-printed resin (Group B: IV–VII), each subjected to distinct postprocessing protocols. Water sorption (wsp) and solubility (wsl) were measured after immersion in distilled water at 37 °C for 24, 48, and 72 h, and 7 and 14 days. Surface topography and nanoroughness were assessed using atomic force microscopy (AFM). Statistical descriptive analyses were followed by correlation analyses. Milled PMMA demonstrated significantly lower water sorption and negative solubility (mass loss), indicating material dissolution. In contrast, 3D-printed PMMA showed higher water sorption and positive solubility (mass gain), reflecting water incorporation and polymer swelling. The kinetic profiles differed: milled PMMA displayed a monophasic absorption curve, while 3D-printed PMMA exhibited a biphasic pattern with accelerated water uptake after 72 h. AFM analysis revealed that 3D-printed surfaces had significantly greater nanoroughness than milled surfaces. Strong positive correlations were observed between surface roughness parameters (Sa, Sy) and water sorption capacity. The fabrication method was found to influence the hydrolytic stability of PMMA dental materials. Milled PMMA demonstrated superior stability, with lower water uptake, smoother surfaces, and lower leaching solubility. In contrast, 3D-printed PMMA exhibited increased surface roughness and water sorption, attributed to its layered microstructure and nanoporosity. Surface topography emerged as a strong predictor of wsl, related to hydrolytic degradation. For clinical applications, milled PMMA is recommended for long-term use requiring durability, whereas 3D-printed PMMA may be appropriate for short-term applications with optimised postprocessing.

Schlagwörter

Stichwörter der Autor:innen

3D printingCAD/CAM millingdental PMMAhydrolytic stabilitysurface roughnesstopographic characteristicswater sorption

Autor:innen und Institutionen

  • Department of Dental Prostheses Technology (Dental Technology), Center for Advanced Technologies in Dental Prosthodontics, Faculty of Dental Medicine, "Victor Babeș" University of Medicine and Pharmacy Timișoara, Eftimi…
  • National Institute for Research and Development in Electrochemistry and Condensed Matter, 300569 Timisoara, Romania.
  • Department of Functional Science, Medical Informatics and Biostatistics, "Victor Babeș" University of Medicine and Pharmacy Timișoara, Eftimie Murgu Sq. No. 2, 300041 Timisoara, Romania.
  • Department of Preventive, Community Dentistry and Oral Health, Center for Advanced Technologies in Dental Prosthodontics, Faculty of Dental Medicine, "Victor Babeș" University of Medicine and Pharmacy Timișoara, Eftimie…

ORCID-Profile: Liliana Porojan, Flavia Roxana Bejan, Mihaela Ionela Gherban, Anamaria Matichescu

Zitieren

APA

Porojan, L., Bejan, F. R., Vasiliu, R. D., Gherban, M. I., Moleriu, L. C., & Matichescu, A. (2026). Surface Characteristics and Hydrolytic Stability in Milled and 3D-Printed PMMA Dental Materials. Polymers, 18(5), 597. https://doi.org/10.3390/polym18050597

Vancouver

Porojan L, Bejan FR, Vasiliu RD, Gherban MI, Moleriu LC, Matichescu A. Surface Characteristics and Hydrolytic Stability in Milled and 3D-Printed PMMA Dental Materials. Polymers. 2026;18(5):597. doi:10.3390/polym18050597

BibTeX
@article{Porojan2026,
  author = {Porojan, Liliana and Bejan, Flavia Roxana and Vasiliu, Roxana Diana and Gherban, Mihaela Ionela and Moleriu, Lavinia Cristina and Matichescu, Anamaria},
  title = {Surface Characteristics and Hydrolytic Stability in Milled and 3D-Printed PMMA Dental Materials},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {5},
  pages = {597},
  doi = {10.3390/polym18050597}
}
Kostenlos starten →