EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of Resin Type, Layer Thickness, and Printing Orientation on the Mechanical and Surface Properties of 3D-Printed Occlusal Splints

Beyza Tandogan iD, Faruk Emir iD, Gulsum Ceylan iD

Polymers · 21.01.2026 · 18 (2) · 290

DOI: 10.3390/polym18020290 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 21.01.2026. Verfasst von Beyza Tandogan und 2 weiteren Autor:innen. Beteiligte Einrichtung: Graduate School of Health Sciences, Department of Prosthodontics, Istanbul Medipol University, Fatih 34810, Istanbul, Turkey. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 46 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Istanbul Medipol University, Istanbul Medipol University Scientific Research Projects.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This in vitro study aimed to evaluate the effects of resin type, layer thickness, and printing orientation on the surface and mechanical properties of 3D-printed occlusal splints fabricated using digital light processing (DLP) technology. Three commercially available splint resins (KeySplint Hard, Freeprint Splint 2.0, and V-Print Splint) were used to fabricate 180 rectangular specimens with two-layer thicknesses (50 µm and 100 µm) and three printing orientations (0°, 45°, 90°). Surface roughness (Ra, Rz), gloss, microhardness, flexural strength, and elastic modulus were measured. Statistical analysis was performed using robust ANOVA with Bonferroni correction. Resin type and printing orientation significantly influenced all surface and mechanical properties (p < 0.001), while layer thickness had a limited effect. Keystone resin exhibited the smoothest surface and highest gloss, whereas Freeprint resin showed the highest microhardness and elastic modulus. Printing at 45° generally enhanced flexural strength and provided more balanced mechanical performance. SEM analysis confirmed that surface morphology varied with orientation, correlating with profilometric and gloss measurements. Resin composition and printing orientation are critical determinants of the mechanical and surface performance of 3D-printed occlusal splints. Optimizing these parameters can improve durability, esthetics, and clinical functionality. All tested materials achieved clinically acceptable surface smoothness, supporting their suitability for intraoral use.

Schlagwörter

Stichwörter der Autor:innen

3D printingdigital light processinglayer thicknessocclusal splintprinting orientationresin materials

Autor:innen und Institutionen

  • Graduate School of Health Sciences, Department of Prosthodontics, Istanbul Medipol University, Fatih 34810, Istanbul, Turkey.
  • Department of Prosthodontics, Gülhane Faculty of Dentistry, Health Sciences University, Ankara 06010, Turkey.
  • Department of Prosthodontics, School of Dentistry, Istanbul Medipol University, Ataturk Bulvari, No:27, Unkapani, Fatih 34083, Istanbul, Turkey.

ORCID-Profile: Beyza Tandogan, Faruk Emir, Gulsum Ceylan

Förderung

  • Istanbul Medipol University
  • Istanbul Medipol University Scientific Research Projects

Zitieren

APA

Tandogan, B., Emir, F., & Ceylan, G. (2026). Effect of Resin Type, Layer Thickness, and Printing Orientation on the Mechanical and Surface Properties of 3D-Printed Occlusal Splints. Polymers, 18(2), 290. https://doi.org/10.3390/polym18020290

Vancouver

Tandogan B, Emir F, Ceylan G. Effect of Resin Type, Layer Thickness, and Printing Orientation on the Mechanical and Surface Properties of 3D-Printed Occlusal Splints. Polymers. 2026;18(2):290. doi:10.3390/polym18020290

BibTeX
@article{Tandogan2026,
  author = {Tandogan, Beyza and Emir, Faruk and Ceylan, Gulsum},
  title = {Effect of Resin Type, Layer Thickness, and Printing Orientation on the Mechanical and Surface Properties of 3D-Printed Occlusal Splints},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {2},
  pages = {290},
  doi = {10.3390/polym18020290}
}
Kostenlos starten →