A Comprehensive Investigation of Infill Geometry Effects on the Mechanical Performance of Polymer 3D Printed Components
Polymers · 30.12.2025 · 18 (1) · 111
DOI: 10.3390/polym18010111 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 30.12.2025. Verfasst von Faisal J Alzahrani und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, Faculty of Engineering-Rabigh, King Abdulaziz University, Jeddah 21589, Saudi Arabia. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 33 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Deanship of Scientific Research DSR, Deanship of Scientific Research (DSR) at King Abdulaziz University, Jeddah, Saudi Arabia.
Abstract (Originalsprache)
Fused filament fabrication (FFF, often called FDM) is widely used in polymer additive manufacturing; however, it suffers from mechanical anisotropy and weak bonding in the Z direction. This work examines how the infill pattern influences the tensile response of PLA parts at fixed printing conditions. Dog-bone specimens (PLA, four patterns: grid, honeycomb, rectilinear, adaptive cubic) were printed and tested in tension (n = 3 per pattern). Grid yielded the highest ultimate tensile strength, whereas honeycomb produced the largest Young’s modulus; rectilinear was intermediate and adaptive cubic was trailed in both metrics. X-ray diffraction of printed PLA showed a broad halo at 16–20° (2θ) with weak α-form reflections, consistent with largely amorphous microstructure after FFF. Together, the results indicate that, at constant material and nominal infill, pattern selection alone can shift the strength–stiffness balance, with grid favoring strength and honeycomb favoring stiffness.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Mechanical Engineering, Faculty of Engineering-Rabigh, King Abdulaziz University, Jeddah 21589, Saudi Arabia.
- Department of Mechanical Engineering, Faculty of Engineering, King Abdulaziz University, Jeddah 21589, Saudi Arabia.
- Advanced Material Technologies Institute, Energy and Industry Sector, King Abdulaziz City for Science and Technology, Riyadh 11442, Saudi Arabia.
- Department of Industrial Engineering, Faculty of Engineering-Rabigh, King Abdulaziz University, Jeddah 21589, Saudi Arabia.
ORCID-Profile: Faisal J Alzahrani, Yasser S Alzahrani, Mohammed T Alamoudi, Mojahed Alkhateeb
Förderung
- Deanship of Scientific Research DSR
- Deanship of Scientific Research (DSR) at King Abdulaziz University, Jeddah, Saudi Arabia
Zitieren
APA
Alzahrani, F. J., Alzahrani, Y. S., Alamoudi, M. T., & Alkhateeb, M. (2025). A Comprehensive Investigation of Infill Geometry Effects on the Mechanical Performance of Polymer 3D Printed Components. Polymers, 18(1), 111. https://doi.org/10.3390/polym18010111
Vancouver
Alzahrani FJ, Alzahrani YS, Alamoudi MT, Alkhateeb M. A Comprehensive Investigation of Infill Geometry Effects on the Mechanical Performance of Polymer 3D Printed Components. Polymers. 2025;18(1):111. doi:10.3390/polym18010111
BibTeX
@article{Alzahrani2025,
author = {Alzahrani, Faisal J and Alzahrani, Yasser S and Alamoudi, Mohammed T and Alkhateeb, Mojahed},
title = {A Comprehensive Investigation of Infill Geometry Effects on the Mechanical Performance of Polymer 3D Printed Components},
journal = {Polymers},
year = {2025},
volume = {18},
number = {1},
pages = {111},
doi = {10.3390/polym18010111}
}
EUVIMED