EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Analysis of the Hertz Contact Model for Evaluating Mechanical Properties of Polymers Using the Finite Element Method

Laisvidas Striska, Rokas Astrauskas iD, Nikolajus Kozulinas iD, Dainius Udris iD, Sonata Tolvaisiene iD, Eugenijus Macerauskas, Inga Morkvenaite iD, Arunas Ramanavicius iD

Polymers · 13.11.2025 · 17 (22) · 3018

DOI: 10.3390/polym17223018 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 13.11.2025. Verfasst von Laisvidas Striska und 7 weiteren Autor:innen. Beteiligte Einrichtung: Department of Nanotechnology, Center for Physical Sciences and Technology, Sauletekio al. 3, 10257 Vilnius, Lithuania. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 31 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Inoprogress, European Union.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Atomic force microscopy (AFM) is widely used to quantify mechanical properties, typically Young’s modulus, by fitting force–indentation data with various mathematical contact models. However, results across laboratories often diverge, and the causes remain unresolved. Here, we interrogate the methodology by which mechanical properties are defined in AFM indentation and identify key limitations of the Hertz model, the standard model for determining mechanical properties, notably that the contact radius is not directly determined, which limits the accuracy of the estimated Young’s modulus. We hypothesize that this inference systematically overestimates the true tip–sample contact, which inflates the contact area and thereby underestimates Young’s modulus. This bias is amplified under large indentation conditions, which are frequently used in soft-material studies. To isolate and clarify the issue, we focus on a well-characterized polymer, polyvinyl chloride (PVC), using it as a controlled testbed for contact radius overestimation. Our analysis is focused on the contact radius and Hertz-based extraction of Young’s modulus. We determined the contact radius and Young’s modulus using AFM with two different probes: a sphere with a 20 nm radius (SPHERE20) and a sphere with a 2 µm radius (SPHERE2000). The results were compared to macroscopic data obtained using a standard measurement (ISO 527-1:2019) of Young’s modulus. The contact was modeled using finite element analysis (FEA). The dependence of the contact radius on the indentation was compared to the Hertz model. The results from FEA fit corrected contact radius values, and it is smaller by 15.46% (SPHERE20) and 57.9% (SPHERE2000) than those calculated by the Hertz model.

Schlagwörter

Stichwörter der Autor:innen

Young’s modulusatomic force microscopecontact radiuselastic modulusfinite element analysispolymer

Autor:innen und Institutionen

  • Department of Nanotechnology, Center for Physical Sciences and Technology, Sauletekio al. 3, 10257 Vilnius, Lithuania.
  • Department of Electrical Engineering, Vilnius Gediminas Technical University, Plytines g. 25, 10105 Vilnius, Lithuania.
  • Faculty of Mathematics and Informatics, Vilnius University, 01513 Vilnius, Lithuania.
  • Department of Physical Chemistry, Vilnius University, Naugarduko g. 24, 03225 Vilnius, Lithuania.

ORCID-Profile: Rokas Astrauskas, Nikolajus Kozulinas, Dainius Udris, Sonata Tolvaisiene, Inga Morkvenaite, Arunas Ramanavicius

Förderung

  • Inoprogress
  • European Union

Zitieren

APA

Striska, L., Astrauskas, R., Kozulinas, N., Udris, D., Tolvaisiene, S., Macerauskas, E., Morkvenaite, I., & Ramanavicius, A. (2025). Analysis of the Hertz Contact Model for Evaluating Mechanical Properties of Polymers Using the Finite Element Method. Polymers, 17(22), 3018. https://doi.org/10.3390/polym17223018

Vancouver

Striska L, Astrauskas R, Kozulinas N, Udris D, Tolvaisiene S, Macerauskas E, et al. Analysis of the Hertz Contact Model for Evaluating Mechanical Properties of Polymers Using the Finite Element Method. Polymers. 2025;17(22):3018. doi:10.3390/polym17223018

BibTeX
@article{Striska2025,
  author = {Striska, Laisvidas and Astrauskas, Rokas and Kozulinas, Nikolajus and Udris, Dainius and Tolvaisiene, Sonata and Macerauskas, Eugenijus and Morkvenaite, Inga and Ramanavicius, Arunas},
  title = {Analysis of the Hertz Contact Model for Evaluating Mechanical Properties of Polymers Using the Finite Element Method},
  journal = {Polymers},
  year = {2025},
  volume = {17},
  number = {22},
  pages = {3018},
  doi = {10.3390/polym17223018}
}
Kostenlos starten →