EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Improvement of Contact Models by Finite Element Analysis for the Evaluation of Yeast Mechanical Properties

Laisvidas Striska, Nikolajus Kozulinas iD, Rokas Astrauskas iD, Dainius Udris iD, Audrius Grainys, Sonata Tolvaisiene iD, Juste Rozene iD, Tomas Mockaitis iD, Arunas Ramanavicius iD, Inga Morkvenaite iD

Materials · 03.07.2026 · 19 (13) · 2837

DOI: 10.3390/ma19132837 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 03.07.2026. Verfasst von Laisvidas Striska und 9 weiteren Autor:innen. Beteiligte Einrichtung: Department of Nanotechnology, Center for Physical Sciences and Technology, Sauletekio al. 3, 10257 Vilnius, Lithuania. Die Arbeit nennt 39 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: European Union.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this work, we extended our previous studies on the limitations of classical contact models from polymers to a biological system. We used yeast as a model system to investigate how contact evolution during indentation affects the accuracy of AFM-based determination of Young’s modulus. We proposed a practical correction framework for the classical Hertz and Sneddon flat-punch models to improve the extraction of mechanical properties from experimental data. Force-indentation curves were measured using a spherical (SPHERE) probe with a 2 μm radius and a flat (FLAT) probe with a 4 μm radius of plateau. The experimental results were analyzed using both corrected and uncorrected contact models, while a finite element analysis (FEA) model was used to determine the contact radius-indentation dependence. It showed that Young’s modulus estimated from AFM indentation using classical formulations is probe-dependent because the contact radius is inadequately described. By incorporating the FEA-derived effective contact radius into Hertz and Sneddon contact models, the same Young’s modulus was obtained for yeast with both probes and compared to reference values with other techniques. These findings establish contact evolution as a governing factor in AFM-based cell mechanics and provide a practical route toward robust, probe-independent, and more accurate determination of mechanical properties for living cells.

Schlagwörter

Stichwörter der Autor:innen

Hertz modelSneddon flat-punch modelYoung’s modulusatomic force microscopecontact evolutioncontact radiusfinite element analysisliving cellsyeast

Autor:innen und Institutionen

  • Department of Nanotechnology, Center for Physical Sciences and Technology, Sauletekio al. 3, 10257 Vilnius, Lithuania.
  • Department of Electrical Engineering, Vilnius Gediminas Technical University, Plytines g. 25, 10105 Vilnius, Lithuania.
  • Faculty of Mathematics and Informatics, Vilnius University, 01513 Vilnius, Lithuania.
  • Department of Mechatronics, Robotics, and Digital Manufacturing, Vilnius Gediminas Technical University, Plytines g. 25, 10105 Vilnius, Lithuania.
  • Department of Chemistry and Bioengineering, Vilnius Gediminas Technical University, Sauletekio al. 11, 10223 Vilnius, Lithuania.
  • Department of Physical Chemistry, Vilnius University, Naugarduko g. 24, 03225 Vilnius, Lithuania.

ORCID-Profile: Nikolajus Kozulinas, Rokas Astrauskas, Dainius Udris, Sonata Tolvaisiene, Juste Rozene, Tomas Mockaitis, Arunas Ramanavicius, Inga Morkvenaite

Förderung

  • European Union

Zitieren

APA

Striska, L., Kozulinas, N., Astrauskas, R., Udris, D., Grainys, A., Tolvaisiene, S., Rozene, J., Mockaitis, T., Ramanavicius, A., & Morkvenaite, I. (2026). Improvement of Contact Models by Finite Element Analysis for the Evaluation of Yeast Mechanical Properties. Materials, 19(13), 2837. https://doi.org/10.3390/ma19132837

Vancouver

Striska L, Kozulinas N, Astrauskas R, Udris D, Grainys A, Tolvaisiene S, et al. Improvement of Contact Models by Finite Element Analysis for the Evaluation of Yeast Mechanical Properties. Materials. 2026;19(13):2837. doi:10.3390/ma19132837

BibTeX
@article{Striska2026,
  author = {Striska, Laisvidas and Kozulinas, Nikolajus and Astrauskas, Rokas and Udris, Dainius and Grainys, Audrius and Tolvaisiene, Sonata and Rozene, Juste and Mockaitis, Tomas and Ramanavicius, Arunas and Morkvenaite, Inga},
  title = {Improvement of Contact Models by Finite Element Analysis for the Evaluation of Yeast Mechanical Properties},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {13},
  pages = {2837},
  doi = {10.3390/ma19132837}
}
Kostenlos starten →