EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effects of Sterilization Processes with Hydrogen Peroxide and Ethylene Oxide on Commercial 3D-Printed PLA, PLA-FC, and PETG by Fused Deposition Modeling

Jorge Mauricio Fuentes iD, Homero Cadena iD, Abel Remache iD, Omar Flor-Unda iD, Santiago Sarria iD, Jonathan Delgado iD, Pablo Bonilla iD, Santiago Ferrándiz iD

Polymers · 27.10.2025 · 17 (21) · 2864

DOI: 10.3390/polym17212864 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 27.10.2025. Verfasst von Jorge Mauricio Fuentes und 7 weiteren Autor:innen. Beteiligte Einrichtung: Ingeniería en Diseño Industrial e Ingeniería Mecánica, Facultad de Ingeniería y Ciencias Aplicadas, Universidad Central del Ecuador, Quito 170521, Ec…. Die Arbeit wurde bisher 8-mal zitiert (Crossref) und nennt 41 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Universidad de las Américas, Quito, Ecuador, Dirección de Investigación, Universidad Central del Ecuador.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Polymers such as PLA, PLA reinforced with carbon fiber (PLA + CF), and PETG are widely employed in utensils, structural components, and biomedical device housings where load-bearing capability and chemical resistance are desirable. This is particularly relevant for reusable applications in which sterilization with hydrogen peroxide (HP) or ethylene oxide (EO) is often required. In this study, the impact of HP and EO sterilization processes on the mechanical, thermal, and structural properties of PLA, PLA + CF, and PETG was evaluated. The mechanical properties assessed included elongation at break, elastic modulus, and tensile strength after sterilization. The thermal properties examined comprised thermal stability and the coefficient of thermal expansion (CTE). Additionally, Fourier Transform Infrared Spectroscopy (FTIR) was performed to detect potential alterations in functional groups. For PLA, sterilization with HP and EO resulted in a 22% increase in ultimate tensile strength (UTS) and a 21% increase in elastic modulus, accompanied by a noticeable reduction in ductility and the appearance of more brittle fracture surfaces. PLA + CF exhibited greater stability under both sterilization methods due to the reinforcing effect of carbon fibers. In the case of PETG, tensile strength and stiffness remained stable; however, HP sterilization led to a remarkable increase in elongation at break (294%), whereas EO sterilization reduced it. Regarding thermal properties, glass transition temperature (Tg) showed variations: PLA presented either an increase or decrease in Tg depending on the sterilization treatment, PLA + CF displayed a Tg reduction after EO sterilization, while PETG exhibited a moderate Tg increase under HP sterilization. CTE decreased at lower temperatures but increased after EO treatment. FTIR analysis revealed only minor chemical modifications induced by sterilization. Overall, HP and EO sterilization can be safely applied to additively manufactured medical components based on these polymers, provided that the structures are not subjected to high mechanical loads and do not require strict dimensional tolerances.

Schlagwörter

Stichwörter der Autor:innen

3D FDM3D printingPETGPLAPLAFCethylene oxidehydrogen peroxidepolymer sterilization

Autor:innen und Institutionen

  • Ingeniería en Diseño Industrial e Ingeniería Mecánica, Facultad de Ingeniería y Ciencias Aplicadas, Universidad Central del Ecuador, Quito 170521, Ecuador.
  • Ingeniería Industrial, Facultad de Ingeniería y Ciencias Aplicadas, Universidad de Las Américas, Quito 170125, Ecuador.
  • Departamento de Ingeniería Mecánica y de Materiales, Instituto de Tecnología de Materiales, Universitat Politécnica de València, Plaza Ferrándiz y Carbonell s/n, 03801 Alcoi, Spain.

ORCID-Profile: Jorge Mauricio Fuentes, Homero Cadena, Abel Remache, Omar Flor-Unda, Santiago Sarria, Jonathan Delgado, Pablo Bonilla, Santiago Ferrándiz

Förderung

  • Universidad de las Américas, Quito, Ecuador
  • Dirección de Investigación, Universidad Central del Ecuador

Zitieren

APA

Fuentes, J. M., Cadena, H., Remache, A., Flor-Unda, O., Sarria, S., Delgado, J., Bonilla, P., & Ferrándiz, S. (2025). Effects of Sterilization Processes with Hydrogen Peroxide and Ethylene Oxide on Commercial 3D-Printed PLA, PLA-FC, and PETG by Fused Deposition Modeling. Polymers, 17(21), 2864. https://doi.org/10.3390/polym17212864

Vancouver

Fuentes JM, Cadena H, Remache A, Flor-Unda O, Sarria S, Delgado J, et al. Effects of Sterilization Processes with Hydrogen Peroxide and Ethylene Oxide on Commercial 3D-Printed PLA, PLA-FC, and PETG by Fused Deposition Modeling. Polymers. 2025;17(21):2864. doi:10.3390/polym17212864

BibTeX
@article{Fuentes2025,
  author = {Fuentes, Jorge Mauricio and Cadena, Homero and Remache, Abel and Flor-Unda, Omar and Sarria, Santiago and Delgado, Jonathan and Bonilla, Pablo and Ferrándiz, Santiago},
  title = {Effects of Sterilization Processes with Hydrogen Peroxide and Ethylene Oxide on Commercial 3D-Printed PLA, PLA-FC, and PETG by Fused Deposition Modeling},
  journal = {Polymers},
  year = {2025},
  volume = {17},
  number = {21},
  pages = {2864},
  doi = {10.3390/polym17212864}
}
Kostenlos starten →