Isothermal Crystallization Kinetics and Their Effect on the Molding Process and Mechanical Properties of PAEK and PEEK
Polymers · 09.10.2025 · 17 (19) · 2713
DOI: 10.3390/polym17192713 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 09.10.2025. Verfasst von Jindong Zhang und 7 weiteren Autor:innen. Beteiligte Einrichtung: National Key Laboratory of Advanced Composites, AVIC Composite Technology Center, AVIC Composite Corporation Ltd., Beijing 101300, China. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 34 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
The crystallization behavior of poly(aryletherketone) (PAEK) determines its applicable molding process and profoundly affects its mechanical properties. However, research on the crystallization behavior of new PAEKs and their impact on performance is still insufficient. In this work, the isothermal crystallization behavior of a novel PAEK was studied and compared with that of standard poly(etheretherketone) (PEEK). The influence of molding temperatures on the mechanical properties of thermoplastics was revealed by controlling the crystallization temperatures and analyzing the crystallization behavior. The results indicate that due to the disruption of the molecular structure regularity of PAEK, its melting temperature for primary crystallization is generally about 30 °C lower than that of PEEK, which is beneficial for its molding at lower temperatures. At the same undercooling level, the crystallization rate of PAEK is lower than that of PEEK, making it easier to control the crystallinity of PAEK through process parameters. The crystallinity of the thermoplastics increases with the increase in soaking time, thereby improving their tensile strength and modulus. The maximum crystallinity of PAEK is approximately 20.5%, which is lower than PEEK’s value of 31.8%. Therefore, under the same undercooling condition, the tensile strength and modulus of PEEK increase by up to 29.5% and 17.1%, respectively, compared to PAEK. Therefore, by precisely controlling the molding process parameters of PAEK, their crystallization behavior can be managed, enabling the achievement of various properties as needed.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- National Key Laboratory of Advanced Composites, AVIC Composite Technology Center, AVIC Composite Corporation Ltd., Beijing 101300, China.
- State Key Laboratory of Advanced Fiber Materials, Center for Advanced Low-Dimension Materials, College of Materials Science and Engineering, Donghua University, Shanghai 201620, China.
- Advanced Technology and Equipment Research Institute, Beijing University of Chemical Technology, Beijing 100029, China.
ORCID-Profile: Jindong Zhang
Zitieren
APA
Zhang, J., Yu, K., Luo, Y., Li, W., Zhong, X., Liu, G., Bao, J., & Chen, C. (2025). Isothermal Crystallization Kinetics and Their Effect on the Molding Process and Mechanical Properties of PAEK and PEEK. Polymers, 17(19), 2713. https://doi.org/10.3390/polym17192713
Vancouver
Zhang J, Yu K, Luo Y, Li W, Zhong X, Liu G, et al. Isothermal Crystallization Kinetics and Their Effect on the Molding Process and Mechanical Properties of PAEK and PEEK. Polymers. 2025;17(19):2713. doi:10.3390/polym17192713
BibTeX
@article{Zhang2025,
author = {Zhang, Jindong and Yu, Kun and Luo, Yunfeng and Li, Weidong and Zhong, Xiangyu and Liu, Gang and Bao, Jianwen and Chen, Chunhai},
title = {Isothermal Crystallization Kinetics and Their Effect on the Molding Process and Mechanical Properties of PAEK and PEEK},
journal = {Polymers},
year = {2025},
volume = {17},
number = {19},
pages = {2713},
doi = {10.3390/polym17192713}
}
EUVIMED