EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Early Biological Response to Poly(ε-caprolactone) PCL—Bioactive Glass Composites Obtained by 3D Printing as Bone Substitutes

Alessandro Mosca Balma iD, Riccardo Pedraza iD, Ilaria Roato iD, Clarissa Orrico iD, Sara Meinardi iD, Stefano Bertinetti iD, Tullio Genova iD, Giovanna Gautier di Confiengo iD, Maria Giulia Faga, Donatella Duraccio iD, Giulio Malucelli iD, Marta Miola iD und 2 weitere

Polymers · 15.08.2025 · 17 (16) · 2229

DOI: 10.3390/polym17162229 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 15.08.2025. Verfasst von Alessandro Mosca Balma und 13 weiteren Autor:innen. Beteiligte Einrichtung: Bone and Dental Bioengineering Laboratory, CIR Dental School, Department of Surgical Sciences, University of Turin, 10126 Turin, Italy. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 66 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministero dell'università e della ricerca, Italian Ministry of University and Research (MUR).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The increasing demand for smart bone substitutes has boosted the implementation of biomaterials possibly endowed with both pro-osteogenic and pro-angiogenic capabilities, among which bioactive glasses hold great potential. Hence, two Poly(ε-caprolactone) (PCL)-based composites were loaded at 10 wt.%, with either pristine (SBA3) or copper-doped (SBA3_Cu) silica-based bioactive glasses, through a solvent casting method with chloroform. Neat PCL was used as a control. Samples produced by 3D printing underwent SEM and EDX analyses, and the following were measured: tensile strength and hardness, surface roughness, ion release through ICP-OES, surface free energy, and optical contact angle. Adipose-derived mesenchymal stem cells (ASCs) and human microvascular endothelial cells (HMEC-1) were used to test the biocompatibility of the materials through cell adhesion, spreading, and viability assays. A significant improvement in tensile strength and hardness was observed especially with Cu-doped composites. Both SBA3 and SBA3_Cu added to the PCL favored the early adhesion and the proliferation of HMEC-1 after 3 and 7 days, while ASCs proliferated significantly the most on the SBA-containing composite, at all the time points. Cellular morphology analysis highlighted interesting adaptation patterns to the samples. Further biological characterizations are needed to understand thoroughly how specific bioactive glasses may interact with different cellular types.

Schlagwörter

Stichwörter der Autor:innen

3D printingPoly(ε-caprolactone)adipose-derived mesenchymal stem cellsbioactive glasscell viabilitycopper-dopedearly cell responsesolvent casting

Autor:innen und Institutionen

  • Bone and Dental Bioengineering Laboratory, CIR Dental School, Department of Surgical Sciences, University of Turin, 10126 Turin, Italy.
  • Department of Mechanical and Aerospace Engineering, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Turin, Italy.
  • Institute of Sciences and Technologies for Sustainable Energy and Mobility, National Council of Research, Strada delle Cacce 73, 10135 Turin, Italy.
  • Department of Life Sciences and Systems Biology, University of Torino, Via Accademia Albertina 13, 10123 Torino, Italy.
  • Department of Chemistry, University of Torino, Via P. Giuria 7, 10125 Torino, Italy.
  • Department of Applied Science and Technology, Politecnico di Torino, Viale T. Michel 5, 15121 Alessandria, Italy.

ORCID-Profile: Alessandro Mosca Balma, Riccardo Pedraza, Ilaria Roato, Clarissa Orrico, Sara Meinardi, Stefano Bertinetti, Tullio Genova, Giovanna Gautier di Confiengo, Donatella Duraccio, Giulio Malucelli, Marta Miola, Enrica Verné, Federico Mussano

Förderung

  • Ministero dell'università e della ricerca
  • Italian Ministry of University and Research (MUR)

Zitieren

APA

Mosca Balma, A., Pedraza, R., Roato, I., Orrico, C., Meinardi, S., Bertinetti, S., Genova, T., Gautier di Confiengo, G., Faga, M. G., Duraccio, D., Malucelli, G., Miola, M., Verné, E., & Mussano, F. (2025). Early Biological Response to Poly(ε-caprolactone) PCL—Bioactive Glass Composites Obtained by 3D Printing as Bone Substitutes. Polymers, 17(16), 2229. https://doi.org/10.3390/polym17162229

Vancouver

Mosca Balma A, Pedraza R, Roato I, Orrico C, Meinardi S, Bertinetti S, et al. Early Biological Response to Poly(ε-caprolactone) PCL—Bioactive Glass Composites Obtained by 3D Printing as Bone Substitutes. Polymers. 2025;17(16):2229. doi:10.3390/polym17162229

BibTeX
@article{MoscaBalma2025,
  author = {Mosca Balma, Alessandro and Pedraza, Riccardo and Roato, Ilaria and Orrico, Clarissa and Meinardi, Sara and Bertinetti, Stefano and Genova, Tullio and Gautier di Confiengo, Giovanna and Faga, Maria Giulia and Duraccio, Donatella and Malucelli, Giulio and Miola, Marta and Verné, Enrica and Mussano, Federico},
  title = {Early Biological Response to Poly(ε-caprolactone) PCL—Bioactive Glass Composites Obtained by 3D Printing as Bone Substitutes},
  journal = {Polymers},
  year = {2025},
  volume = {17},
  number = {16},
  pages = {2229},
  doi = {10.3390/polym17162229}
}
Kostenlos starten →