Influence of Different Adhesives and Surface Treatments on Shear and Tensile Bond Strength and Microleakage with Micro-CT of Repaired Bulk-Fill Composites
Polymers · 17.06.2025 · 17 (12) · 1680
DOI: 10.3390/polym17121680 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 17.06.2025. Verfasst von Handan Yıldırım-Işık und 1 weiteren Autor:innen. Beteiligte Einrichtung: Department of Restorative Dentistry, Faculty of Dentistry, Istanbul Beykent University, 34500 Istanbul, Turkey. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 33 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Istanbul Beykent University.
Abstract (Originalsprache)
The repair of defective composite restorations, particularly bulk-fill composites, offers a conservative alternative to complete replacement. However, establishing durable adhesion between aged and fresh composites remains a clinical challenge due to the altered surface properties of aged materials. This in vitro study investigated the effects of different surface treatment protocols (no treatment, diamond bur roughening, and air abrasion) and adhesive systems (G-Premio Bond, Clearfil SE Bond, and Adper Single Bond 2) on the shear bond strength (µSBS), tensile bond strength (µTBS), and microleakage of repaired bulk-fill composites. Results demonstrated that both surface treatment and adhesive type significantly affected bond strength (p < 0.05). Mechanical surface treatments, particularly diamond bur roughening and air abrasion, enhanced µSBS and µTBS compared to untreated controls. The highest µSBS and µTBS values were observed with diamond bur treatment combined with Adper Single Bond 2, reaching mean values of 25.8 ± 2.1 MPa and 28.3 ± 1.8 MPa, respectively. Air abrasion with Clearfil SE Bond also significantly increased bond strengths (µSBS: 22.1 ± 2.0 MPa; µTBS: 23.5 ± 1.7 MPa) relative to no treatment (p < 0.05). Micro-computed tomography analysis revealed that Clearfil SE Bond following diamond bur roughening resulted in the lowest microleakage scores, with a mean leakage volume of 0.12 ± 0.04 µm. These findings underscore the importance of mechanical surface conditioning and appropriate adhesive selection to enhance both bond strength and sealing efficacy in composite repair procedures.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Restorative Dentistry, Faculty of Dentistry, Istanbul Beykent University, 34500 Istanbul, Turkey.
- Heath Services Vocational School, Trakya University, 22030 Edirne, Turkey.
ORCID-Profile: Handan Yıldırım-Işık, Mediha Büyükgöze-Dindar
Förderung
- Istanbul Beykent University
Zitieren
APA
Yıldırım-Işık, H., & Büyükgöze-Dindar, M. (2025). Influence of Different Adhesives and Surface Treatments on Shear and Tensile Bond Strength and Microleakage with Micro-CT of Repaired Bulk-Fill Composites. Polymers, 17(12), 1680. https://doi.org/10.3390/polym17121680
Vancouver
Yıldırım-Işık H, Büyükgöze-Dindar M. Influence of Different Adhesives and Surface Treatments on Shear and Tensile Bond Strength and Microleakage with Micro-CT of Repaired Bulk-Fill Composites. Polymers. 2025;17(12):1680. doi:10.3390/polym17121680
BibTeX
@article{YldrmIk2025,
author = {Yıldırım-Işık, Handan and Büyükgöze-Dindar, Mediha},
title = {Influence of Different Adhesives and Surface Treatments on Shear and Tensile Bond Strength and Microleakage with Micro-CT of Repaired Bulk-Fill Composites},
journal = {Polymers},
year = {2025},
volume = {17},
number = {12},
pages = {1680},
doi = {10.3390/polym17121680}
}
EUVIMED