EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

3D-Printed PLA Mechanical and Viscoelastic Behavior Dependence on the Nozzle Temperature and Printing Orientation

Lykourgos C Kontaxis iD, Dimos Zachos iD, Aliona Georgali-Fickel, Diana V Portan, Stefanos P Zaoutsos, George C Papanicolaou iD

Polymers · 28.03.2025 · 17 (7) · 913

DOI: 10.3390/polym17070913 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 28.03.2025. Verfasst von Lykourgos C Kontaxis und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering and Aeronautics, University of Patras, 26504 Patras, Greece. Die Arbeit wurde bisher 19-mal zitiert (Crossref) und nennt 42 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The present study focuses on the mechanical and viscoelastic characterization of 3D-printed PLA, fabricated in three different printing orientations (0°, 45°, and 90°) and four different nozzle temperatures (210, 220, 230, and 240 °C). By employing a combination of static and dynamic mechanical analysis (DMA) testing, as well as differential scanning calorimetry (DSC) analysis, this work aims to investigate the relationship between processing parameters and the resulting properties of PLA. DSC results showed that higher nozzle temperatures enhance the degree of crystallinity, which in turn affects the mechanical and viscoelastic behavior of PLA. Regardless of the nozzle temperature, the flexural strength decreased as the printing orientation degrees increased. However, it was found that the higher the nozzle temperature, the higher the flexural strength for the same orientation, and the smaller the strength deviations per specimen. DMA results indicated that as the printing orientation increased, glass transition temperature (Tg) values increased while storage modulus values decreased. At the same time, in both cases, by increasing nozzle temperature, an increase in Tg and a respective increase in storage modulus values is observed due to the increase in the degree of crystallinity.

Schlagwörter

Stichwörter der Autor:innen

3D-printingdegree of crystallinitydifferential scanning calorimetry (DSC)dynamic mechanical analysis (DMA)fused deposition modeling (FDM)glass transition region (Tg)mechanical propertiesnozzle temperaturepolylactic acid (PLA)printing orientation

Autor:innen und Institutionen

  • Department of Mechanical Engineering and Aeronautics, University of Patras, 26504 Patras, Greece.
  • Department of Energy Systems, University of Thessaly, 41500 Larisa, Greece.

ORCID-Profile: Lykourgos C Kontaxis, Dimos Zachos, George C Papanicolaou

Zitieren

APA

Kontaxis, L. C., Zachos, D., Georgali-Fickel, A., Portan, D. V., Zaoutsos, S. P., & Papanicolaou, G. C. (2025). 3D-Printed PLA Mechanical and Viscoelastic Behavior Dependence on the Nozzle Temperature and Printing Orientation. Polymers, 17(7), 913. https://doi.org/10.3390/polym17070913

Vancouver

Kontaxis LC, Zachos D, Georgali-Fickel A, Portan DV, Zaoutsos SP, Papanicolaou GC. 3D-Printed PLA Mechanical and Viscoelastic Behavior Dependence on the Nozzle Temperature and Printing Orientation. Polymers. 2025;17(7):913. doi:10.3390/polym17070913

BibTeX
@article{Kontaxis2025,
  author = {Kontaxis, Lykourgos C and Zachos, Dimos and Georgali-Fickel, Aliona and Portan, Diana V and Zaoutsos, Stefanos P and Papanicolaou, George C},
  title = {3D-Printed PLA Mechanical and Viscoelastic Behavior Dependence on the Nozzle Temperature and Printing Orientation},
  journal = {Polymers},
  year = {2025},
  volume = {17},
  number = {7},
  pages = {913},
  doi = {10.3390/polym17070913}
}
Kostenlos starten →