EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Compression Molding of Low-Density Polyethylene Matrix/Glass-Fiber-Reinforced Thick Laminates

Fabrizio Quadrini iD, Giorgio Patrizii iD, Alice Proietti, Leandro Iorio iD, Denise Bellisario iD, Loredana Santo iD

Polymers · 26.09.2024 · 16 (19) · 2722

DOI: 10.3390/polym16192722 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 26.09.2024. Verfasst von Fabrizio Quadrini und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Industrial Engineering, University of Rome "Tor Vergata", Via del Politecnico 1, 00133 Rome, Italy. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 19 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Thermoplastic fiberglass was compression molded in the form of thick panels with a nominal thickness of 10 mm and a size of 300 × 300 mm2. A simplified procedure was adopted to speed up the lamination procedure and adapt it to the aim of recycling waste, glass fibers, fabrics, and thermoplastic films. Low density polyethylene was used as a matrix to simplify the laboratory process, but the same procedure can be extended to other thermoplastic film, such as polyamide. The final thermoplastic composite shows unique properties in terms of its repairability, and its performance was improved by increasing the number of repairing repetitions. For this aim, a repairability test was designed in the bending configuration, and three consecutive cycles of bending/repairing/bending were carried out. The static mechanical properties of the final thermoplastic composite were, conversely, low in comparison with traditional fiberglass because of the choice of a polyethylene matrix. The bending tests showed that the maximum strength was lower than 10 MPa and the elastic modulus was less than 1 GPa. Nevertheless, the toughness of the thermoplastic composite was high, and the samples continued to deform under bending without splitting into two halves.

Schlagwörter

Stichwörter der Autor:innen

compression moldingfiberglassglass fabricslow density polyethylenerecyclingrepairingthermoplastic composites

Autor:innen und Institutionen

  • Department of Industrial Engineering, University of Rome "Tor Vergata", Via del Politecnico 1, 00133 Rome, Italy.

ORCID-Profile: Fabrizio Quadrini, Giorgio Patrizii, Leandro Iorio, Denise Bellisario, Loredana Santo

Zitieren

APA

Quadrini, F., Patrizii, G., Proietti, A., Iorio, L., Bellisario, D., & Santo, L. (2024). Compression Molding of Low-Density Polyethylene Matrix/Glass-Fiber-Reinforced Thick Laminates. Polymers, 16(19), 2722. https://doi.org/10.3390/polym16192722

Vancouver

Quadrini F, Patrizii G, Proietti A, Iorio L, Bellisario D, Santo L. Compression Molding of Low-Density Polyethylene Matrix/Glass-Fiber-Reinforced Thick Laminates. Polymers. 2024;16(19):2722. doi:10.3390/polym16192722

BibTeX
@article{Quadrini2024,
  author = {Quadrini, Fabrizio and Patrizii, Giorgio and Proietti, Alice and Iorio, Leandro and Bellisario, Denise and Santo, Loredana},
  title = {Compression Molding of Low-Density Polyethylene Matrix/Glass-Fiber-Reinforced Thick Laminates},
  journal = {Polymers},
  year = {2024},
  volume = {16},
  number = {19},
  pages = {2722},
  doi = {10.3390/polym16192722}
}
Kostenlos starten →