EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Determination of Residual Stresses in 3D-Printed Polymer Parts

Madina Issametova iD, Nikita V Martyushev iD, Abilkaiyr Zhastalap, Layla B Sabirova, Uderbayeva Assemgul iD, Arailym Tursynbayeva, Gazel Abilezova

Polymers · 19.07.2024 · 16 (14) · 2067

DOI: 10.3390/polym16142067 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 19.07.2024. Verfasst von Madina Issametova und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, Institute of Energy and Mechanical Engineering, Satbayev University, Almaty KZ-050000, Kazakhstan. Die Arbeit wurde bisher 22-mal zitiert (Crossref) und nennt 52 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Science and Higher Education of the Republic of Kazakhstan.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This paper presents the results of an investigation of the possibility of the reliable determination of the residual stress–strain state in polymers and composites using a combination of bridge curvature, optical scanning, and finite element methods. A three-factor experiment was conducted to determine the strength of printed PLA plastic products. The effect of the residual stresses on the strength of the printed products was evaluated. By comparing the values of the same strength stresses, a relationship between the nature of the stresses and the strength of the samples was found. A tendency of the negative influence of tensile stresses and the opposite strengthening effect of compressive stresses was obvious, so at the same values of tensile strength, the value of residual stress of 42.9 MPa is lower than that of the fibre compression at the value of 88.9 MPa. The proposed new methods of the residual stress determination allow obtaining a complete picture of the stressed state of the material in the investigated areas of the products. This may be necessary in confirming the calculated models of the residual stress–strain state, clarifying the strength criteria and assessing the quality of the selected technological modes of manufacturing the products.

Schlagwörter

Stichwörter der Autor:innen

3D printingPLA plasticmathematical modelmechanical characteristicsprocess parametersresidual stressestechnological process

Autor:innen und Institutionen

  • Department of Mechanical Engineering, Institute of Energy and Mechanical Engineering, Satbayev University, Almaty KZ-050000, Kazakhstan.
  • Information Technology Department, Tomsk Polytechnic University, 634050 Tomsk, Russia.

ORCID-Profile: Madina Issametova, Nikita V Martyushev, Uderbayeva Assemgul

Förderung

  • Ministry of Science and Higher Education of the Republic of Kazakhstan

Zitieren

APA

Issametova, M., Martyushev, N. V., Zhastalap, A., Sabirova, L. B., Assemgul, U., Tursynbayeva, A., & Abilezova, G. (2024). Determination of Residual Stresses in 3D-Printed Polymer Parts. Polymers, 16(14), 2067. https://doi.org/10.3390/polym16142067

Vancouver

Issametova M, Martyushev NV, Zhastalap A, Sabirova LB, Assemgul U, Tursynbayeva A, et al. Determination of Residual Stresses in 3D-Printed Polymer Parts. Polymers. 2024;16(14):2067. doi:10.3390/polym16142067

BibTeX
@article{Issametova2024,
  author = {Issametova, Madina and Martyushev, Nikita V and Zhastalap, Abilkaiyr and Sabirova, Layla B and Assemgul, Uderbayeva and Tursynbayeva, Arailym and Abilezova, Gazel},
  title = {Determination of Residual Stresses in 3D-Printed Polymer Parts},
  journal = {Polymers},
  year = {2024},
  volume = {16},
  number = {14},
  pages = {2067},
  doi = {10.3390/polym16142067}
}
Kostenlos starten →