EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Enhancing Sustainability in PLA Membrane Preparation through the Use of Biobased Solvents

Giovanna Gomez d'Ayala, Tiziana Marino, Yêda Medeiros Bastos de Almeida, Anna Raffaela de Matos Costa, Larissa Bezerra da Silva iD, Pietro Argurio iD, Paola Laurienzo iD

Polymers · 16.07.2024 · 16 (14) · 2024

DOI: 10.3390/polym16142024 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 16.07.2024. Verfasst von Giovanna Gomez d'Ayala und 6 weiteren Autor:innen. Beteiligte Einrichtung: Institute of Polymers, Composites and Biomaterials, National Research Council (IPCB-CNR), Via Campi Flegrei, 34, 80078 Pozzuoli, NA, Italy. Die Arbeit wurde bisher 17-mal zitiert (Crossref) und nennt 65 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

For the first time, ultrafiltration (UF) green membranes were prepared through a sustainable route by using PLA as a biopolymer and dihydrolevoclucosenone, whose trade name is Cyrene™ (Cyr), dimethyl isosorbide (DMI), and ethyl lactate (EL) as biobased solvents. The influence of physical-chemical properties of the solvent on the final membrane morphology and performance was evaluated. The variation of polymer concentration in the casting solution, as well as the presence of Pluronic® (Plu) as a pore former agent, were assessed as well. The obtained results highlighted that the final morphology of a membrane was strictly connected with the interplaying of thermodynamic factors as well as kinetic ones, primarily dope solution viscosity. The pore size of the resulting PLA membranes ranged from 0.02 to 0.09 μm. Membrane thickness and porosity varied in the range of 0.090–0.133 mm of 75–87%, respectively, and DMI led to the most porous membranes. The addition of Plu to the casting solution showed a beneficial effect on the membrane contact angle, allowing the formation of hydrophilic membranes (contact angle < 90°), and promoted the increase of pore size as well as the reduction of membrane crystallinity. PLA membranes were tested for pure water permeability (10–390 L/m2 h bar).

Schlagwörter

Stichwörter der Autor:innen

NIPSbiobased solventsbiopolymergreen membranespolylactic acid

Autor:innen und Institutionen

  • Institute of Polymers, Composites and Biomaterials, National Research Council (IPCB-CNR), Via Campi Flegrei, 34, 80078 Pozzuoli, NA, Italy.
  • Department of Chemical Engineering, Federal University of Pernambuco, Recife 50740-520, PE, Brazil.
  • CICECO-Aveiro Institute of Materials, Department of Chemistry, University of Aveiro, 3810-193 Aveiro, Portugal.
  • Postgraduate Program in Materials Science and Engineering, Federal University of Rio Grande do Norte, Natal 59078-970, RN, Brazil.
  • Department of Environmental Engineering, DIAm, University of Calabria, Via Pietro Bucci CUBO 44/A, 87036 Rende, CS, Italy.

ORCID-Profile: Larissa Bezerra da Silva, Pietro Argurio, Paola Laurienzo

Zitieren

APA

Gomez d'Ayala, G., Marino, T., de Almeida, Y. M. B., Costa, A. R. M., Bezerra da Silva, L., Argurio, P., & Laurienzo, P. (2024). Enhancing Sustainability in PLA Membrane Preparation through the Use of Biobased Solvents. Polymers, 16(14), 2024. https://doi.org/10.3390/polym16142024

Vancouver

Gomez d'Ayala G, Marino T, de Almeida YMB, Costa ARM, Bezerra da Silva L, Argurio P, et al. Enhancing Sustainability in PLA Membrane Preparation through the Use of Biobased Solvents. Polymers. 2024;16(14):2024. doi:10.3390/polym16142024

BibTeX
@article{GomezdAyala2024,
  author = {Gomez d'Ayala, Giovanna and Marino, Tiziana and de Almeida, Yêda Medeiros Bastos and Costa, Anna Raffaela de Matos and Bezerra da Silva, Larissa and Argurio, Pietro and Laurienzo, Paola},
  title = {Enhancing Sustainability in PLA Membrane Preparation through the Use of Biobased Solvents},
  journal = {Polymers},
  year = {2024},
  volume = {16},
  number = {14},
  pages = {2024},
  doi = {10.3390/polym16142024}
}
Kostenlos starten →