EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Assessment of Binder Modification in Dry-Added Waste Plastic Modified Asphalt

Soheil Heydari iD, Nioushasadat Haji Seyed Javadi iD, Hamid Bayat, Ailar Hajimohammadi iD

Polymers · 11.07.2024 · 16 (14) · 1987

DOI: 10.3390/polym16141987 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 11.07.2024. Verfasst von Soheil Heydari und 3 weiteren Autor:innen. Beteiligte Einrichtung: School of Civil and Environmental Engineering, University of New South Wales, Sydney, NSW 2052, Australia. Die Arbeit wurde bisher 14-mal zitiert (Crossref) und nennt 78 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: CRC-P, Cooperative Research Centre Project (CRC-P).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Plastic production has risen steadily, but recycling rates lag. Researchers are increasingly investigating the use of plastics in road construction, especially in terms of modifying asphalt with waste plastics. The dry process, which involves incorporating plastics into hot aggregates, is increasingly gaining traction as an alternative to the wet process, where plastics are added to hot bitumen. Past studies indicate enhanced asphalt mixture properties with the dry process, but there is debate about the role of waste plastics—whether they should be used as aggregates, fillers, or binder modifiers. This study explores the extent to which dry-added waste plastic modified the binder of the asphalt mixtures. Fluorescent microscopy and scanning electron microscopy revealed the impact of plastic on the binder, while image analysis quantified polymer swelling and dispersion in the binder matrix. It was concluded that when plastics are added to hot aggregates, they will act as binder modifiers. Lower plastic content and reduced polymer crystallinity led to increased polymer swelling and better dispersion in the mixture. This study recommends plastic inclusion of less than 2.5% (by volume) in the dry-added method since high plastic content leads to polymer agglomeration, especially for highly crystalline polymers. Additionally, mixes modified with amorphous plastics exhibited superior workability and performance compared to those modified with crystalline plastics. This study also suggests that using plastics to replace both bitumen and filler can improve cost efficiency, reduce the carbon footprint, and enhance the overall performance of the asphalt mixture.

Schlagwörter

Stichwörter der Autor:innen

bitumen modificationdry processmodified asphalt mixturepolyethylenepolymer modified bitumenwaste plastics

Autor:innen und Institutionen

  • School of Civil and Environmental Engineering, University of New South Wales, Sydney, NSW 2052, Australia.

ORCID-Profile: Soheil Heydari, Nioushasadat Haji Seyed Javadi, Ailar Hajimohammadi

Förderung

  • CRC-P
  • Cooperative Research Centre Project (CRC-P)

Zitieren

APA

Heydari, S., Haji Seyed Javadi, N., Bayat, H., & Hajimohammadi, A. (2024). Assessment of Binder Modification in Dry-Added Waste Plastic Modified Asphalt. Polymers, 16(14), 1987. https://doi.org/10.3390/polym16141987

Vancouver

Heydari S, Haji Seyed Javadi N, Bayat H, Hajimohammadi A. Assessment of Binder Modification in Dry-Added Waste Plastic Modified Asphalt. Polymers. 2024;16(14):1987. doi:10.3390/polym16141987

BibTeX
@article{Heydari2024,
  author = {Heydari, Soheil and Haji Seyed Javadi, Nioushasadat and Bayat, Hamid and Hajimohammadi, Ailar},
  title = {Assessment of Binder Modification in Dry-Added Waste Plastic Modified Asphalt},
  journal = {Polymers},
  year = {2024},
  volume = {16},
  number = {14},
  pages = {1987},
  doi = {10.3390/polym16141987}
}
Kostenlos starten →