EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Thermomechanical Material Characterization of Polyethylene Terephthalate Glycol with 30% Carbon Fiber for Large-Format Additive Manufacturing of Polymer Structures

Katie A Martin, Guillermo A Riveros iD, Travis L Thornell iD, Zackery B McClelland, Elton L Freeman, James T Stinson

Polymers · 04.07.2024 · 16 (13) · 1913

DOI: 10.3390/polym16131913 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 04.07.2024. Verfasst von Katie A Martin und 5 weiteren Autor:innen. Beteiligte Einrichtung: Geotechnical and Structures Laboratory (GSL) at the US Army Corps of Engineers (USACE) Engineer Research and Development Center (ERDC), 3909 Halls Fe…. Die Arbeit wurde bisher 14-mal zitiert (Crossref) und nennt 39 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: U.S. Army Engineer Research and Development Center, Directors, Information Technology and Geotechnical and Structural Laboratory.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Large-format additive manufacturing (LFAM) is used to print large-scale polymer structures. Understanding the thermal and mechanical properties of polymers suitable for large-scale extrusion is needed for design and production capabilities. An in-house-built LFAM printer was used to print polyethylene terephthalate glycol with 30% carbon fiber (PETG CF30%) samples for thermomechanical characterization. Thermogravimetric analysis (TGA) shows that the samples were 30% carbon fiber by weight. X-ray microscopy (XRM) and porosity studies find 25% voids/volume for undried material and 1.63% voids/volume for dry material. Differential scanning calorimetry (DSC) shows a glass transition temperature (Tg) of 66 °C, while dynamic mechanical analysis (DMA) found Tg as 82 °C. The rheology indicated that PETG CF30% is a good printing material at 220–250 °C. Bending experiments show an average of 48.5 MPa for flexure strength, while tensile experiments found an average tensile strength of 25.0 MPa at room temperature. Comparison with 3D-printed PLA and PETG from the literature demonstrated that LFAM-printed PETG CF30% had a comparative high Young’s modulus and had similar tensile strength. For design purposes, prints from LFAM should consider both material choice and print parameters, especially when considering large layer heights.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturing (AM)bead-layer-printcarbon fiber (CF)compositeslarge-format additive manufacturing (LFAM)polyethylene terephthalate glycol (PETG)thermomechanical characterization

Autor:innen und Institutionen

  • Geotechnical and Structures Laboratory (GSL) at the US Army Corps of Engineers (USACE) Engineer Research and Development Center (ERDC), 3909 Halls Ferry Rd., Vicksburg, MS 39180, USA.
  • Information Technology Laboratory (ITL) at the US Army Corps of Engineers (USACE) Engineer Research and Development Center (ERDC), 3909 Halls Ferry Rd., Vicksburg, MS 39180, USA.

ORCID-Profile: Guillermo A Riveros, Travis L Thornell

Förderung

  • U.S. Army Engineer Research and Development Center
  • Directors, Information Technology and Geotechnical and Structural Laboratory

Zitieren

APA

Martin, K. A., Riveros, G. A., Thornell, T. L., McClelland, Z. B., Freeman, E. L., & Stinson, J. T. (2024). Thermomechanical Material Characterization of Polyethylene Terephthalate Glycol with 30% Carbon Fiber for Large-Format Additive Manufacturing of Polymer Structures. Polymers, 16(13), 1913. https://doi.org/10.3390/polym16131913

Vancouver

Martin KA, Riveros GA, Thornell TL, McClelland ZB, Freeman EL, Stinson JT. Thermomechanical Material Characterization of Polyethylene Terephthalate Glycol with 30% Carbon Fiber for Large-Format Additive Manufacturing of Polymer Structures. Polymers. 2024;16(13):1913. doi:10.3390/polym16131913

BibTeX
@article{Martin2024,
  author = {Martin, Katie A and Riveros, Guillermo A and Thornell, Travis L and McClelland, Zackery B and Freeman, Elton L and Stinson, James T},
  title = {Thermomechanical Material Characterization of Polyethylene Terephthalate Glycol with 30% Carbon Fiber for Large-Format Additive Manufacturing of Polymer Structures},
  journal = {Polymers},
  year = {2024},
  volume = {16},
  number = {13},
  pages = {1913},
  doi = {10.3390/polym16131913}
}
Kostenlos starten →