Influence of Choline Chloride/Urea and Glycerol Plasticizers on the Mechanical Properties of Thermoplastic Starch Plastics
Polymers · 09.03.2024 · 16 (6) · 751
DOI: 10.3390/polym16060751 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 09.03.2024. Verfasst von Jacob Staker und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Chemistry and Chemical Biology, Indiana University-Purdue University Indianapolis, Indianapolis, IN 46202, USA. Die Arbeit wurde bisher 18-mal zitiert (Crossref) und nennt 31 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Center for Research and Learning (CRL) MURI Program at Indiana University-Purdue University Indianapolis.
Abstract (Originalsprache)
Bio-based plastics made of food-safe compostable materials, such as thermoplastic starch (TPS), can be designed into films that have potential to replace many non-biodegradable single-use plastic (SUP) items. TPS film characteristics, such as elongation at break and tensile strength, are largely affected by the choice of the plasticizers used in formulation. Our work identifies the mechanical properties and the chemical structural differences between TPS films made with two different plasticizer mixtures that have not yet been compared alongside one another: deep eutectic solvent choline chloride/urea (1:2) (CC:U) and glycerol with an acetic acid catalyst (AA:G). Potato-based TPS samples were formed by mixing each plasticizer with a consistent amount of potato starch and distilled water with heat. After gelation formation, the viscous TPS mixture was centrifuged to degas and extruded. Films were dried at controlled room temperature. Characterization included the tensile testing of coupons according to ASTM (American Society of Testing and Materials) standard D638, attenuated total reflectance Fourier-transform infrared (ATR-FTIR) spectroscopy, X-ray diffraction (XRD), melting point (MP), and scanning electron microscopy (SEM). The AA:G films displayed significantly higher tensile strength (M = 2.04 ± 1.24 MPa) than the CC:U films (M = 0.18 ± 0.08 MPa); however, the CC:U films had higher elongation at break (M = 47.2 ± 3.6%) than the AA:G films (M = 31.1 ± 12.6%). This can be explained by the difference in functional groups, composition, and the degree of crystallinity evidenced by the FTIR, XRD, MP, and SEM results. Our findings suggest that potato-based TPS films with an AA:G plasticizer mixture hold promise for SUP applications that require more strength, while CC:U films may be more suited for wraps and bags that require flexibility. These innovations can aid to mitigate the environmental impact of harmful plastic waste.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Chemistry and Chemical Biology, Indiana University-Purdue University Indianapolis, Indianapolis, IN 46202, USA.
- Department of Mechanical and Energy Engineering, Indiana University-Purdue University Indianapolis, Indianapolis, IN 46202, USA.
- Department of Earth and Environmental Sciences, Indiana University-Purdue University Indianapolis, Indianapolis, IN 46202, USA.
ORCID-Profile: Amanda P Siegel, Andres Tovar
Förderung
- Center for Research and Learning (CRL) MURI Program at Indiana University-Purdue University Indianapolis
Zitieren
APA
Staker, J., Schott, S., Singh, R., Collier, K., Druschel, G., Siegel, A. P., & Tovar, A. (2024). Influence of Choline Chloride/Urea and Glycerol Plasticizers on the Mechanical Properties of Thermoplastic Starch Plastics. Polymers, 16(6), 751. https://doi.org/10.3390/polym16060751
Vancouver
Staker J, Schott S, Singh R, Collier K, Druschel G, Siegel AP, et al. Influence of Choline Chloride/Urea and Glycerol Plasticizers on the Mechanical Properties of Thermoplastic Starch Plastics. Polymers. 2024;16(6):751. doi:10.3390/polym16060751
BibTeX
@article{Staker2024,
author = {Staker, Jacob and Schott, Sydney and Singh, Riya and Collier, Kourtney and Druschel, Gregory and Siegel, Amanda P and Tovar, Andres},
title = {Influence of Choline Chloride/Urea and Glycerol Plasticizers on the Mechanical Properties of Thermoplastic Starch Plastics},
journal = {Polymers},
year = {2024},
volume = {16},
number = {6},
pages = {751},
doi = {10.3390/polym16060751}
}
EUVIMED