EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Three-Dimensional-Printed Sodium Alginate and k-Carrageenan-Based Scaffolds with Potential Biomedical Applications

Cristina Stavarache, Sorina Alexandra Gȃrea, Andrada Serafim iD, Elena Olăreț iD, George Mihail Vlăsceanu, Maria Minodora Marin, Horia Iovu

Polymers · 23.01.2024 · 16 (3) · 305

DOI: 10.3390/polym16030305 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 23.01.2024. Verfasst von Cristina Stavarache und 6 weiteren Autor:innen. Beteiligte Einrichtung: Advanced Polymer Materials Group, National University of Science and Technology POLITEHNICA București, 1-7 Gh. Polizu Street, 011061 Bucharest, Roman…. Die Arbeit wurde bisher 17-mal zitiert (Crossref) und nennt 40 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National University for Science and Technology POLITEHNICA București.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This work reports the development of a marine-derived polysaccharide formulation based on k-Carrageenan and sodium alginate in order to produce a novel scaffold for engineering applications. The viscoelastic properties of the bicomponent inks were assessed via rheological tests prior to 3D printing. Compositions with different weight ratios between the two polymers, without any crosslinker, were subjected to 3D printing for the first time, to the best of our knowledge, and the fabrication parameters were optimized to ensure a controlled architecture. Crosslinking of the 3D-printed scaffolds was performed in the presence of a chloride mixture (CaCl2:KCl = 1:1; v/v) of different concentrations. The efficiency of the crosslinking protocol was evaluated in terms of swelling behavior and mechanical properties. The swelling behavior indicated a decrease in the swelling degree when the concentration of the crosslinking agent was increased. These results are consistent with the nanoindentation measurements and the results of the macro-scale tests. Moreover, morphology analysis was also used to determine the pore size of the samples upon freeze-drying and the uniformity and micro-architectural characteristics of the scaffolds. Overall, the registered results indicated that the bicomponent ink, Alg/kCG = 1:1 may exhibit potential for tissue-engineering applications.

Schlagwörter

Stichwörter der Autor:innen

3D printinginterpenetrated networks hydrogels scaffoldsk-Carrageenansodium alginate

Autor:innen und Institutionen

  • Advanced Polymer Materials Group, National University of Science and Technology POLITEHNICA București, 1-7 Gh. Polizu Street, 011061 Bucharest, Romania.
  • "C.D. Neniţescu" Institute of Organic and Supramolecular Chemistry, 202-B Splaiul Independentei, 060023 Bucharest, Romania.
  • Faculty of Medical Engineering, National University of Science and Technology POLITEHNICA Bucuresti, 1-7 Gh. Polizu Street, 011061 Bucharest, Romania.
  • Academy of Romanian Scientists, 54 Splaiul Independentei, 050094 Bucharest, Romania.

ORCID-Profile: Andrada Serafim, Elena Olăreț

Förderung

  • National University for Science and Technology POLITEHNICA București

Zitieren

APA

Stavarache, C., Gȃrea, S. A., Serafim, A., Olăreț, E., Vlăsceanu, G. M., Marin, M. M., & Iovu, H. (2024). Three-Dimensional-Printed Sodium Alginate and k-Carrageenan-Based Scaffolds with Potential Biomedical Applications. Polymers, 16(3), 305. https://doi.org/10.3390/polym16030305

Vancouver

Stavarache C, Gȃrea SA, Serafim A, Olăreț E, Vlăsceanu GM, Marin MM, et al. Three-Dimensional-Printed Sodium Alginate and k-Carrageenan-Based Scaffolds with Potential Biomedical Applications. Polymers. 2024;16(3):305. doi:10.3390/polym16030305

BibTeX
@article{Stavarache2024,
  author = {Stavarache, Cristina and Gȃrea, Sorina Alexandra and Serafim, Andrada and Olăreț, Elena and Vlăsceanu, George Mihail and Marin, Maria Minodora and Iovu, Horia},
  title = {Three-Dimensional-Printed Sodium Alginate and k-Carrageenan-Based Scaffolds with Potential Biomedical Applications},
  journal = {Polymers},
  year = {2024},
  volume = {16},
  number = {3},
  pages = {305},
  doi = {10.3390/polym16030305}
}
Kostenlos starten →