EUVIMEDOpdag EUVIMED
Open access · CC BY 4.0

High-Cycle Fatigue Behaviour of Polyetheretherketone (PEEK) Produced by Additive Manufacturing

Pedro Rendas iD, Alexandre Imperadeiro, Rui F Martins iD, Bruno A R Soares

Polymers · 2023-12-20 · 16 (1) · 18

DOI: 10.3390/polym16010018 ↗

At a glance

Journal article in Polymers, published online on 2023-12-20. Written by Pedro Rendas and 3 co-authors. Institution: UNIDEMI, Department of Mechanical and Industrial Engineering, NOVA School of Science and Technology, Universidade NOVA de Lisboa, 2829-516 Caparica, …. Cited 22 times so far (Crossref); 64 references. The full text is freely available (open access, CC BY 4.0). Funded by: Fundação para a Ciência e Tecnologia, Fundação para a Ciência e a Tecnologia (FCT-MCTES).

AbstractSubjectsBibliografiske oplysningerCiteRelated studies

Abstract (original language)

Polyetheretherketone (PEEK) is the leading high-performance thermoplastic biomaterial that can be processed through material extrusion (ME) additive manufacturing (AM), also known as three-dimensional (3D) printing, for patient-specific load-bearing implant manufacture. Considering the importance of cyclic loading for load-bearing implant design, this work addresses the high-cycle fatigue behaviour of 3D-printed PEEK. In this work, printed PEEK specimens are cyclically loaded under stress-controlled tension–tension using different stress levels between 75% and 95% of printed PEEK’s tensile strength. The experimental results are used to document 3D-printed PEEK’s fatigue behaviour using Basquin’s power law, which was compared with previous fatigue research on bulk PEEK and other 3D-printing materials. As a pioneering study on its fatigue behaviour, the results from this work show that 3D-printed PEEK exhibits an above-average fatigue strength of 65 MPa, corresponding to about 75% of its tensile strength. Fracture surface analysis suggests that a transition can occur from ductile to brittle fracture with maximum stresses between 85% and 95% of the tensile strength. Evidence of crack propagation features on fracture surfaces under scanning electron microscope (SEM) observation suggests crack initiation in void defects created by printing deposition that propagates longitudinally through line bonding interfaces along layers. Considering this, 3D-printed PEEK’s fatigue behaviour can be strongly related to printing conditions. Further research on the fatigue behaviour of 3D-printed PEEK is necessary to support its use in load-bearing implant applications.

Subjects

Author keywords

Polyetheretherketone (PEEK)additive manufacturingmaterial extrusionmechanical properties

Authors and institutions

  • UNIDEMI, Department of Mechanical and Industrial Engineering, NOVA School of Science and Technology, Universidade NOVA de Lisboa, 2829-516 Caparica, Portugal.
  • Laboratório Associado de Sistemas Inteligentes, 4800-058 Guimarães, Portugal.

ORCID profiles: Pedro Rendas, Rui F Martins

Funding

  • Fundação para a Ciência e Tecnologia
  • Fundação para a Ciência e a Tecnologia (FCT-MCTES)

Cite

APA

Rendas, P., Imperadeiro, A., Martins, R. F., & Soares, B. A. R. (2023). High-Cycle Fatigue Behaviour of Polyetheretherketone (PEEK) Produced by Additive Manufacturing. Polymers, 16(1), 18. https://doi.org/10.3390/polym16010018

Vancouver

Rendas P, Imperadeiro A, Martins RF, Soares BAR. High-Cycle Fatigue Behaviour of Polyetheretherketone (PEEK) Produced by Additive Manufacturing. Polymers. 2023;16(1):18. doi:10.3390/polym16010018

BibTeX
@article{Rendas2023,
  author = {Rendas, Pedro and Imperadeiro, Alexandre and Martins, Rui F and Soares, Bruno A R},
  title = {High-Cycle Fatigue Behaviour of Polyetheretherketone (PEEK) Produced by Additive Manufacturing},
  journal = {Polymers},
  year = {2023},
  volume = {16},
  number = {1},
  pages = {18},
  doi = {10.3390/polym16010018}
}
Start for free →