High-Cycle Fatigue Behaviour of Polyetheretherketone (PEEK) Produced by Additive Manufacturing
Polymers · 20.12.2023 · 16 (1) · 18
DOI: 10.3390/polym16010018 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 20.12.2023. Verfasst von Pedro Rendas und 3 weiteren Autor:innen. Beteiligte Einrichtung: UNIDEMI, Department of Mechanical and Industrial Engineering, NOVA School of Science and Technology, Universidade NOVA de Lisboa, 2829-516 Caparica, …. Die Arbeit wurde bisher 22-mal zitiert (Crossref) und nennt 64 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Fundação para a Ciência e Tecnologia, Fundação para a Ciência e a Tecnologia (FCT-MCTES).
Abstract (Originalsprache)
Polyetheretherketone (PEEK) is the leading high-performance thermoplastic biomaterial that can be processed through material extrusion (ME) additive manufacturing (AM), also known as three-dimensional (3D) printing, for patient-specific load-bearing implant manufacture. Considering the importance of cyclic loading for load-bearing implant design, this work addresses the high-cycle fatigue behaviour of 3D-printed PEEK. In this work, printed PEEK specimens are cyclically loaded under stress-controlled tension–tension using different stress levels between 75% and 95% of printed PEEK’s tensile strength. The experimental results are used to document 3D-printed PEEK’s fatigue behaviour using Basquin’s power law, which was compared with previous fatigue research on bulk PEEK and other 3D-printing materials. As a pioneering study on its fatigue behaviour, the results from this work show that 3D-printed PEEK exhibits an above-average fatigue strength of 65 MPa, corresponding to about 75% of its tensile strength. Fracture surface analysis suggests that a transition can occur from ductile to brittle fracture with maximum stresses between 85% and 95% of the tensile strength. Evidence of crack propagation features on fracture surfaces under scanning electron microscope (SEM) observation suggests crack initiation in void defects created by printing deposition that propagates longitudinally through line bonding interfaces along layers. Considering this, 3D-printed PEEK’s fatigue behaviour can be strongly related to printing conditions. Further research on the fatigue behaviour of 3D-printed PEEK is necessary to support its use in load-bearing implant applications.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- UNIDEMI, Department of Mechanical and Industrial Engineering, NOVA School of Science and Technology, Universidade NOVA de Lisboa, 2829-516 Caparica, Portugal.
- Laboratório Associado de Sistemas Inteligentes, 4800-058 Guimarães, Portugal.
ORCID-Profile: Pedro Rendas, Rui F Martins
Förderung
- Fundação para a Ciência e Tecnologia
- Fundação para a Ciência e a Tecnologia (FCT-MCTES)
Zitieren
APA
Rendas, P., Imperadeiro, A., Martins, R. F., & Soares, B. A. R. (2023). High-Cycle Fatigue Behaviour of Polyetheretherketone (PEEK) Produced by Additive Manufacturing. Polymers, 16(1), 18. https://doi.org/10.3390/polym16010018
Vancouver
Rendas P, Imperadeiro A, Martins RF, Soares BAR. High-Cycle Fatigue Behaviour of Polyetheretherketone (PEEK) Produced by Additive Manufacturing. Polymers. 2023;16(1):18. doi:10.3390/polym16010018
BibTeX
@article{Rendas2023,
author = {Rendas, Pedro and Imperadeiro, Alexandre and Martins, Rui F and Soares, Bruno A R},
title = {High-Cycle Fatigue Behaviour of Polyetheretherketone (PEEK) Produced by Additive Manufacturing},
journal = {Polymers},
year = {2023},
volume = {16},
number = {1},
pages = {18},
doi = {10.3390/polym16010018}
}
EUVIMED