Water Sorption in Hybrid Polyester/Glass/Jute Composites Processed via Compression Molding and Vacuum-Assisted Resin Transfer Molding
Polymers · 16.11.2023 · 15 (22) · 4438
DOI: 10.3390/polym15224438 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 16.11.2023. Verfasst von Rudá Aranha und 7 weiteren Autor:innen. Beteiligte Einrichtung: Escuela de Ingeniería Mecánica, Pontifícia Universidad Católica de Valparaíso 1, Valparaíso 2340025, Chile. Die Arbeit wurde bisher 16-mal zitiert (Crossref) und nennt 67 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: CAPES, CNPq, FAPESQ/PB.
Abstract (Originalsprache)
The aim of this work is to analyze water sorption in hybrid polyester/glass fabric/jute fabric composites molded via compression and VARTM (Vacuum-Assisted Resin Transfer Molding). The laminates were produced with five different stacking sequences and subjected to water sorption testing at room temperature, 50 °C and 70 °C. This study consisted of two stages: experimental and theoretical stages. The composites had a fiber volume content ranging from 30% to 40%. Water absorption and diffusion coefficient in the hybrid composites were intermediate to those reinforced with a single type of fiber. There were no significant differences in these properties based on fiber arrangement once the composites reached saturation. Diffusion coefficient values were higher for specimens with jute fiber on at least one of the outer surfaces. Water sorption rates increased with higher immersion temperatures. The water sorption at saturation point was not affected by the manufacturing process. Among the hybrid composites, those with jute on the surfaces showed the highest diffusion coefficient, while those with glass on the surface had the lowest values. Higher diffusion coefficient values were observed at temperatures of 50 °C and 70 °C. The main influencing factors on the absorbed moisture content for composites are the presence and content of jute fibers in the system and the immersion temperature. The manufacturing process does not affect the water sorption at saturation point.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Escuela de Ingeniería Mecánica, Pontifícia Universidad Católica de Valparaíso 1, Valparaíso 2340025, Chile.
- Post-Graduate Program in Materials Science and Engineering, Federal University of Campina Grande, Campina Grande 58429-900, Brazil.
- Mechanical Engineering Department, Federal University of Campina Grande, Campina Grande 58429-900, Brazil.
- Textil Engineering Department, Federal University of Rio Grande do Norte, Natal 59078-970, Brazil.
ORCID-Profile: José L V Rivera, Antonio G B de Lima, Laura H Carvalho
Förderung
- CAPES
- CNPq
- FAPESQ/PB
Zitieren
APA
Aranha, R., Filho, M. A. A., de Lima Santos, C., Fonseca, V. M., Rivera, J. L. V., de Lima, A. G. B., de Amorim, W. F., & Carvalho, L. H. (2023). Water Sorption in Hybrid Polyester/Glass/Jute Composites Processed via Compression Molding and Vacuum-Assisted Resin Transfer Molding. Polymers, 15(22), 4438. https://doi.org/10.3390/polym15224438
Vancouver
Aranha R, Filho MAA, de Lima Santos C, Fonseca VM, Rivera JLV, de Lima AGB, et al. Water Sorption in Hybrid Polyester/Glass/Jute Composites Processed via Compression Molding and Vacuum-Assisted Resin Transfer Molding. Polymers. 2023;15(22):4438. doi:10.3390/polym15224438
BibTeX
@article{Aranha2023,
author = {Aranha, Rudá and Filho, Mario A Albuquerque and de Lima Santos, Cícero and Fonseca, Viviane M and Rivera, José L V and de Lima, Antonio G B and de Amorim, Wanderley F and Carvalho, Laura H},
title = {Water Sorption in Hybrid Polyester/Glass/Jute Composites Processed via Compression Molding and Vacuum-Assisted Resin Transfer Molding},
journal = {Polymers},
year = {2023},
volume = {15},
number = {22},
pages = {4438},
doi = {10.3390/polym15224438}
}
EUVIMED