EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Photocurable High-Energy Polymer-Based Materials for 3D Printing

Dmitrii Tkachev iD, Yana Dubkova iD, Alexander Zhukov, Yanis Verkhoshanskiy, Alexander Vorozhtsov, Ilya Zhukov iD

Polymers · 28.10.2023 · 15 (21) · 4252

DOI: 10.3390/polym15214252 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 28.10.2023. Verfasst von Dmitrii Tkachev und 5 weiteren Autor:innen. Beteiligte Einrichtung: Laboratory of Metallurgy Nanotechnologies, National Research Tomsk State University, Lenin Avenue, 36, 634050 Tomsk, Russia. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 22 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Russian Science Foundation.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Digital light processing (DLP) or stereolithography is the most promising method of additive manufacturing (3D printing) of products based on high-energy materials due to, first of all, the absence of a high-temperature impact on the material. This paper presents research results of an ultraviolet (UV)-cured urethane methacrylate polymer containing 70 wt.% of high-energy solid powder based on ammonium salts, which is intended for digital light processing. Polymerization of the initial slurry is studied herein. It is shown that the addition of coarse powder transparency for the UV radiation to resin increases its curing depth. The thickness of the layer, which can polymerize, varies from 600 µm to 2 mm when the light power density ranges from 20 to 400 mJ/cm2, respectively. In DLP-based 3D printing, the obtained material density is 92% of the full density, while the compressive strength is 29 ± 3 MPa, and the ultimate tensile strength is 13 ± 1.3 MPa. The thermogravimetric analysis shows the decrease in the thermal decomposition temperature of UV-cured resin with high-energy additives compared to the thermal decomposition temperatures of the initial components separately. Thermal decomposition is accompanied by intensive heat generation. The burning rate of obtained samples grows from 0.74 to 3.68 mm/s, respectively, at the pressure growth from 0.1 to 4 MPa. Based on the results, it can be concluded that DLP-based 3D printing with the proposed UV photocurable resin is rather promising for the fabrication of multicomponent high-energy systems and complex profile parts produced therefrom.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturingburning ratehigh-energy materialsphotopolymerstereolithographystructure

Autor:innen und Institutionen

  • Laboratory of Metallurgy Nanotechnologies, National Research Tomsk State University, Lenin Avenue, 36, 634050 Tomsk, Russia.

ORCID-Profile: Dmitrii Tkachev, Yana Dubkova, Ilya Zhukov

Förderung

  • Russian Science Foundation

Zitieren

APA

Tkachev, D., Dubkova, Y., Zhukov, A., Verkhoshanskiy, Y., Vorozhtsov, A., & Zhukov, I. (2023). Photocurable High-Energy Polymer-Based Materials for 3D Printing. Polymers, 15(21), 4252. https://doi.org/10.3390/polym15214252

Vancouver

Tkachev D, Dubkova Y, Zhukov A, Verkhoshanskiy Y, Vorozhtsov A, Zhukov I. Photocurable High-Energy Polymer-Based Materials for 3D Printing. Polymers. 2023;15(21):4252. doi:10.3390/polym15214252

BibTeX
@article{Tkachev2023,
  author = {Tkachev, Dmitrii and Dubkova, Yana and Zhukov, Alexander and Verkhoshanskiy, Yanis and Vorozhtsov, Alexander and Zhukov, Ilya},
  title = {Photocurable High-Energy Polymer-Based Materials for 3D Printing},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {21},
  pages = {4252},
  doi = {10.3390/polym15214252}
}
Kostenlos starten →