EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Photocurable Polymer-Based 3D Printing: Advanced Flexible Strain Sensors for Human Kinematics Monitoring

Christopher Billings, Ridwan Siddique iD, Yingtao Liu iD

Polymers · 20.10.2023 · 15 (20) · 4170

DOI: 10.3390/polym15204170 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 20.10.2023. Verfasst von Christopher Billings und 2 weiteren Autor:innen. Beteiligte Einrichtung: School of Aerospace and Mechanical Engineering, University of Oklahoma, 865 Asp Ave., Norman, OK 73019, USA. Die Arbeit wurde bisher 11-mal zitiert (Crossref) und nennt 37 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Oklahoma Aerospace and Defense Innovation Institute (OADII) and the Data Institute for Societal Challenges (DISC), University of Oklahoma, the Oklahoma Aerospace and Defense Innovation Institute (OADII), the Data Institute for Societal Challenges (DISC), Office of the Vice President for Research and Partnerships, University of Oklahoma.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Vat photopolymerization-based additive manufacturing (AM) is critical in improving solutions for wearable sensors. The ability to add nanoparticles to increase the polymer resin’s mechanical, electrical, and chemical properties creates a strong proposition for investigating custom nanocomposites for the medical field. This work uses a low-cost biocompatible polymer resin enhanced with multi-walled carbon nanotubes (MWCNTs), and a digital light processing-based AM system to develop accurate strain sensors. These sensors demonstrate the ability to carry a 244% maximum strain while lasting hundreds of cycles without degradation at lower strain ranges. In addition, the printing process allows for detailed prints to be accomplished at a sub-30 micron spatial resolution while also assisting alignment of the MWCNTs in the printing plane. Moreover, high-magnification imagery demonstrates uniform MWCNT dispersion by utilizing planetary shear mixing and identifying MWCNT pullout at fracture locations. Finally, the proposed nanocomposite is used to print customized and wearable strain sensors for finger motion monitoring and can detect different amounts of flexion and extension. The 3D printed nanocomposite sensors demonstrate characteristics that make it a strong candidate for the applications of human kinematics monitoring and sensing.

Schlagwörter

Stichwörter der Autor:innen

3D printingadditive manufacturingflexible sensorphotocurable polymerpiezoresistivitystrain sensorwearable device

Autor:innen und Institutionen

  • School of Aerospace and Mechanical Engineering, University of Oklahoma, 865 Asp Ave., Norman, OK 73019, USA.
  • Norman North High School, 1809 Stubbeman Ave., Norman, OK 73069, USA.

ORCID-Profile: Ridwan Siddique, Yingtao Liu

Förderung

  • Oklahoma Aerospace and Defense Innovation Institute (OADII) and the Data Institute for Societal Challenges (DISC), University of Oklahoma
  • the Oklahoma Aerospace and Defense Innovation Institute (OADII)
  • the Data Institute for Societal Challenges (DISC), Office of the Vice President for Research and Partnerships, University of Oklahoma

Zitieren

APA

Billings, C., Siddique, R., & Liu, Y. (2023). Photocurable Polymer-Based 3D Printing: Advanced Flexible Strain Sensors for Human Kinematics Monitoring. Polymers, 15(20), 4170. https://doi.org/10.3390/polym15204170

Vancouver

Billings C, Siddique R, Liu Y. Photocurable Polymer-Based 3D Printing: Advanced Flexible Strain Sensors for Human Kinematics Monitoring. Polymers. 2023;15(20):4170. doi:10.3390/polym15204170

BibTeX
@article{Billings2023,
  author = {Billings, Christopher and Siddique, Ridwan and Liu, Yingtao},
  title = {Photocurable Polymer-Based 3D Printing: Advanced Flexible Strain Sensors for Human Kinematics Monitoring},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {20},
  pages = {4170},
  doi = {10.3390/polym15204170}
}
Kostenlos starten →