EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Topology Optimization for Digital Light Projector Additive Manufacturing Addressing the In-Situ Structural Strength Issue

Jun Wang, Jikai Liu, Lei Li iD

Polymers · 28.08.2023 · 15 (17) · 3573

DOI: 10.3390/polym15173573 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 28.08.2023. Verfasst von Jun Wang und 2 weiteren Autor:innen. Beteiligte Einrichtung: Center for Advanced Jet Engineering Technologies (CaJET), Key Laboratory of High Efficiency and Clean Mechanical Manufacture, Ministry of Education, …. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 51 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Shandong Provincial Key Research and Development Program, National Key Research and Development Program of China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

A topology optimization approach is proposed for the design of self-supporting structures for digital light projector (DLP) 3D printing. This method accounts for the adhesion forces between the print part and the resin base during DLP printing to avoid failure of the part due to stress concentration and weak connections. Specifically, the effect of the process-related adhesion forces is first simulated by developing a design variable-interpolated finite element model to capture the intricate mechanical behavior during DLP 3D printing. Guided by the process model, a stress-constrained topology optimization algorithm is formulated with both the SIMP and RAMP interpolation schemes. The interpolations on the stress term and the design-dependent adhesion load are carefully investigated. A sensitivity result on the P-norm stress constraint is fully developed. Finally, the approach is applied to several 2D benchmark examples to validate its efficacy in controlling the process-caused peak P-norm stresses. The effects of alternating between the SIMP and RAMP interpolations and changing the stress upper limits are carefully explored during the numerical trials. Moreover, 3D printing tests are performed to validate the improvement in printability when involving the process-related P-norm stress constraint.

Schlagwörter

Stichwörter der Autor:innen

DLP 3D printingdesign for additive manufacturingstress constrainttopology optimization

Autor:innen und Institutionen

  • Center for Advanced Jet Engineering Technologies (CaJET), Key Laboratory of High Efficiency and Clean Mechanical Manufacture, Ministry of Education, School of Mechanical Engineering, Shandong University, Jinan 250061, C…
  • Key National Demonstration Center for Experimental Mechanical Engineering Education, Shandong University, Jinan 250061, China.

ORCID-Profile: Lei Li

Förderung

  • Shandong Provincial Key Research and Development Program
  • National Key Research and Development Program of China

Zitieren

APA

Wang, J., Liu, J., & Li, L. (2023). Topology Optimization for Digital Light Projector Additive Manufacturing Addressing the In-Situ Structural Strength Issue. Polymers, 15(17), 3573. https://doi.org/10.3390/polym15173573

Vancouver

Wang J, Liu J, Li L. Topology Optimization for Digital Light Projector Additive Manufacturing Addressing the In-Situ Structural Strength Issue. Polymers. 2023;15(17):3573. doi:10.3390/polym15173573

BibTeX
@article{Wang2023,
  author = {Wang, Jun and Liu, Jikai and Li, Lei},
  title = {Topology Optimization for Digital Light Projector Additive Manufacturing Addressing the In-Situ Structural Strength Issue},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {17},
  pages = {3573},
  doi = {10.3390/polym15173573}
}
Kostenlos starten →