Topology Optimization of the Clutch Lever Manufactured by Additive Manufacturing
Materials · 03.05.2023 · 16 (9) · 3510
DOI: 10.3390/ma16093510 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 03.05.2023. Verfasst von Aleksandra Mikulikova und 9 weiteren Autor:innen. Beteiligte Einrichtung: Department of Fundamentals of Machinery Design, Faculty of Mechanical Engineering, Silesian University of Technology, 44-100 Gliwice, Poland. Die Arbeit wurde bisher 20-mal zitiert (Crossref) und nennt 48 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Structural Funds of the European Union, Ministry of Education, Youth and Sports of the Czech Republic, project Students Grant Competition.
Abstract (Originalsprache)
This article aims to review a redesign approach of a student racing car’s clutch lever component, which was topologically optimized and manufactured by Additive Manufacturing (AM). Finite Element Method (FEM) analysis was conducted before and after a Topology Optimization (TO) process in order to achieve equivalent stiffness and the desired safety factor for the optimized part. The redesigned clutch lever was manufactured by using AM–Selective Laser Melting (SLM) and printed from powdered aluminum alloy AlSi10Mg. The final evaluation of the study deals with the experimental test and comparison of the redesigned clutch lever with the existing part which was used in the previous racing car. Using TO as a main redesign tool and AM brought significant changes to the optimized part, especially the following: reduced mass of the component (10%), increased stiffness, kept safety factor above the 3.0 value and ensured the more aesthetic design and a good surface quality. Moreover, using TO and AM gave the opportunity to consolidate multi-part assembly into a single component manufactured by one manufacturing process that reduced the production time. The experimental results justified the simulation results and proved that even though the applied load was almost 1.5× higher than the assumed one, the maximum von Mises stress on the component was still below the yield limit of 220 MPa.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Fundamentals of Machinery Design, Faculty of Mechanical Engineering, Silesian University of Technology, 44-100 Gliwice, Poland.
- Department of Machining, Assembly and Engineering Metrology, Faculty of Mechanical Engineering, VSB-Technical University of Ostrava, 70800 Ostrava, Czech Republic.
- Institute of Transport, Faculty of Mechanical Engineering, VSB-Technical University of Ostrava, 17. Listo-padu 15/2172, 70800 Ostrava, Czech Republic.
ORCID-Profile: Aleksandra Mikulikova, Jakub Mesicek, Jiri Hajnys, Quoc-Phu Ma, Ales Sliva, Marek Pagac
Förderung
- Structural Funds of the European Union
- Ministry of Education, Youth and Sports of the Czech Republic
- project Students Grant Competition
- Ministry of Education, Youth and Sports and Faculty of Mechanical Engineering VŠB-TUO
Zitieren
APA
Mikulikova, A., Mesicek, J., Karger, J., Hajnys, J., Ma, Q. P., Sliva, A., Smiraus, J., Srnicek, D., Cienciala, S., & Pagac, M. (2023). Topology Optimization of the Clutch Lever Manufactured by Additive Manufacturing. Materials, 16(9), 3510. https://doi.org/10.3390/ma16093510
Vancouver
Mikulikova A, Mesicek J, Karger J, Hajnys J, Ma QP, Sliva A, et al. Topology Optimization of the Clutch Lever Manufactured by Additive Manufacturing. Materials. 2023;16(9):3510. doi:10.3390/ma16093510
BibTeX
@article{Mikulikova2023,
author = {Mikulikova, Aleksandra and Mesicek, Jakub and Karger, Jan and Hajnys, Jiri and Ma, Quoc-Phu and Sliva, Ales and Smiraus, Jakub and Srnicek, David and Cienciala, Samuel and Pagac, Marek},
title = {Topology Optimization of the Clutch Lever Manufactured by Additive Manufacturing},
journal = {Materials},
year = {2023},
volume = {16},
number = {9},
pages = {3510},
doi = {10.3390/ma16093510}
}
EUVIMED