Analysis of the Stress Field in Photoelasticity Used to Evaluate the Residual Stresses of a Plastic Injection-Molded Part
Polymers · 11.08.2023 · 15 (16) · 3377
DOI: 10.3390/polym15163377 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 11.08.2023. Verfasst von Carlos Vargas-Isaza und 2 weiteren Autor:innen. Beteiligte Einrichtung: Grupo Investigación Materiales Avanzados y Energía, Instituto Tecnológico Metropolitano, Medellín 050034, Colombia. Die Arbeit wurde bisher 21-mal zitiert (Crossref) und nennt 34 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
The degree of quality of thermoplastic injection-molded parts can be established based on their weight, appearance, and defects. However, the conditions of the injection process may induce effects on the mechanical performance of the injected parts, and the residual stresses can cause cracks or early failures when an external load or force is applied. To evaluate these mechanical behaviors, different experimental techniques have been reported in the literature, where digital photoelasticity has stood out both for being a non-contact technique and for achieving quantitative results through sophisticated computational algorithms. Against this background, our proposal consists of analyzing the overall residual stress distribution of parts injected under different molding conditions by using digital photoelasticity. In this case, the specimens are subjected to bending strength tests to identify possible effects of the injection process conditions. The findings show that, at mold temperatures of 80 °C, flow-induced residual stresses increase with packing pressure. However, these internal stress levels do not affect the external load applied by the mechanical bending test, while the mass injected at higher levels of packing pressure helps to increase the bending strength of the injected part. At lower mold temperatures (50 °C), the mechanical strength of the injected part is slightly reduced, possibly due to a lower effect of the packing pressure.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Grupo Investigación Materiales Avanzados y Energía, Instituto Tecnológico Metropolitano, Medellín 050034, Colombia.
- Grupo Investigación Calidad, Metrología y Producción, Instituto Tecnológico Metropolitano, Medellín 050034, Colombia.
- Grupo de Investigación GIIAM, Institución Universitaria Pascual Bravo, Medellín 050034, Colombia.
ORCID-Profile: Juan Posada-Correa
Zitieren
APA
Vargas-Isaza, C., Posada-Correa, J., & Briñez-de León, J. (2023). Analysis of the Stress Field in Photoelasticity Used to Evaluate the Residual Stresses of a Plastic Injection-Molded Part. Polymers, 15(16), 3377. https://doi.org/10.3390/polym15163377
Vancouver
Vargas-Isaza C, Posada-Correa J, Briñez-de León J. Analysis of the Stress Field in Photoelasticity Used to Evaluate the Residual Stresses of a Plastic Injection-Molded Part. Polymers. 2023;15(16):3377. doi:10.3390/polym15163377
BibTeX
@article{VargasIsaza2023,
author = {Vargas-Isaza, Carlos and Posada-Correa, Juan and Briñez-de León, Juan},
title = {Analysis of the Stress Field in Photoelasticity Used to Evaluate the Residual Stresses of a Plastic Injection-Molded Part},
journal = {Polymers},
year = {2023},
volume = {15},
number = {16},
pages = {3377},
doi = {10.3390/polym15163377}
}
EUVIMED