EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Electrical Resistivity of 3D-Printed Polymer Elements

Stanislav Stankevich iD, Jevgenijs Sevcenko, Olga Bulderberga iD, Aleksandrs Dutovs, Donat Erts iD, Maksims Piskunovs, Valerijs Ivanovs, Victor Ivanov, Andrey Aniskevich iD

Polymers · 08.07.2023 · 15 (14) · 2988

DOI: 10.3390/polym15142988 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 08.07.2023. Verfasst von Stanislav Stankevich und 8 weiteren Autor:innen. Beteiligte Einrichtung: Institute for Mechanics of Materials, University of Latvia, Jelgavas St. 3, LV-1004 Riga, Latvia. Die Arbeit wurde bisher 32-mal zitiert (Crossref) und nennt 35 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: European Commission, European Regional Development Fund (ERDF).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

During this study, the resistivity of electrically conductive structures 3D-printed via fused filament fabrication (FFF) was investigated. Electrical resistivity characterisation was performed on various structural levels of the whole 3D-printed body, starting from the single traxel (3D-printed single track element), continuing with monolayer and multilayer formation, finalising with hybrid structures of a basic nonconductive polymer and an electrically conductive one. Two commercial conductive materials were studied: Proto-Pasta and Koltron G1. It was determined that the geometry and resistivity of a single traxel influenced the resistivity of all subsequent structural elements of the printed body and affected its electrical anisotropy. In addition, the results showed that thermal postprocessing (annealing) affected the resistivity of a standalone extruded fibre (extruded filament through a printer nozzle in freefall) and traxel. The effect of Joule heating and piezoresistive properties of hybrid structures with imprinted conductive elements made from Koltron G1 were investigated. Results revealed good thermal stability within 70 °C and considerable piezoresistive response with a gauge factor of 15–25 at both low 0.1% and medium 1.5% elongations, indicating the potential of such structures for use as a heat element and strain gauge sensor in applications involving stiff materials and low elongations.

Schlagwörter

Stichwörter der Autor:innen

Joule heatinganisotropyannealingelectrical resistivityfused filament fabricationmonolayermultilayer structurepiezoresistivitystructural levelstraxel

Autor:innen und Institutionen

  • Institute for Mechanics of Materials, University of Latvia, Jelgavas St. 3, LV-1004 Riga, Latvia.
  • Institute of Chemical Physics, University of Latvia, Jelgavas St. 1, LV-1004 Riga, Latvia.
  • ZRF Ritec SIA, Gustava Zemgala St. 71A, LV-1039 Riga, Latvia.

ORCID-Profile: Stanislav Stankevich, Olga Bulderberga, Donat Erts, Andrey Aniskevich

Förderung

  • European Commission
  • European Regional Development Fund (ERDF)

Zitieren

APA

Stankevich, S., Sevcenko, J., Bulderberga, O., Dutovs, A., Erts, D., Piskunovs, M., Ivanovs, V., Ivanov, V., & Aniskevich, A. (2023). Electrical Resistivity of 3D-Printed Polymer Elements. Polymers, 15(14), 2988. https://doi.org/10.3390/polym15142988

Vancouver

Stankevich S, Sevcenko J, Bulderberga O, Dutovs A, Erts D, Piskunovs M, et al. Electrical Resistivity of 3D-Printed Polymer Elements. Polymers. 2023;15(14):2988. doi:10.3390/polym15142988

BibTeX
@article{Stankevich2023,
  author = {Stankevich, Stanislav and Sevcenko, Jevgenijs and Bulderberga, Olga and Dutovs, Aleksandrs and Erts, Donat and Piskunovs, Maksims and Ivanovs, Valerijs and Ivanov, Victor and Aniskevich, Andrey},
  title = {Electrical Resistivity of 3D-Printed Polymer Elements},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {14},
  pages = {2988},
  doi = {10.3390/polym15142988}
}
Kostenlos starten →