EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

A Study on Mechanical Properties of Low-Cost Thermoplastic-Based Materials for Material Extrusion Additive Manufacturing

Mihaela-Raluca Condruz iD, Alexandru Paraschiv iD, Teodor-Adrian Badea iD, Daniel Useriu, Tiberius-Florian Frigioescu, Gabriel Badea iD, Grigore Cican

Polymers · 08.07.2023 · 15 (14) · 2981

DOI: 10.3390/polym15142981 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 08.07.2023. Verfasst von Mihaela-Raluca Condruz und 6 weiteren Autor:innen. Beteiligte Einrichtung: Romanian Research and Development Institute for Gas Turbines COMOTI, 220D Iuliu Maniu Av., 061126 Bucharest, Romania. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 46 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Nucleu" Program through The National Plan for Research, Development and Innovation 2022-2027, funded by the Romanian Ministry of Research, Innovation and Digit…, The APC was funded by the Romanian Minister of Research, Innovation and Digitalization (MCID) through Program 1 - Development of the National Research and Deve…, Romanian Ministry of Research, Innovation and Digitization (MCID).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The present research focused on studying the mechanical properties of three commercially available thermoplastic-based materials used for the additive manufacturing (AM) fused filament deposition (FFD) method. The scientific motivation for the study was the limited information available in the literature regarding the materials’ properties, the inconsistencies that were recorded by other scientists between the materials’ properties and the technical datasheets and the anisotropic behavior of additively manufactured materials. Thereby, it was considered of great importance to perform an extensive study on several materials’ mechanical properties, such as tensile properties and flexural properties. Three materials were tested, Tough PLA, nGen CF10 and UltraFuse PAHT CF15. The tests consisted of monotonic tensile tests, open-hole tensile tests and three-point bending tests. The tests were assisted also with the use of microscopical investigations. Framed specimens’ configurations with two different raster orientations (90°/0° and −45°/+45°) were manufactured using an in-house-developed 3D printing equipment. The best mechanical performances were recorded for UltraFuse PAHT CF15. The 90°/0° raster orientations ensured the highest tensile, open-hole tensile and flexural strength, regardless of the material type, while the −45°/+45° raster orientations ensured the highest elongation values. The analysis showed the importance of the experimental validation of materials for AM.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturingcompositesextrusionopen-hole tensiletensile

Autor:innen und Institutionen

  • Romanian Research and Development Institute for Gas Turbines COMOTI, 220D Iuliu Maniu Av., 061126 Bucharest, Romania.

ORCID-Profile: Mihaela-Raluca Condruz, Alexandru Paraschiv, Teodor-Adrian Badea, Gabriel Badea

Förderung

  • Nucleu" Program through The National Plan for Research, Development and Innovation 2022-2027, funded by the Romanian Ministry of Research, Innovation and Digit…
  • The APC was funded by the Romanian Minister of Research, Innovation and Digitalization (MCID) through Program 1 - Development of the National Research and Deve…
  • Romanian Ministry of Research, Innovation and Digitization (MCID)

Zitieren

APA

Condruz, M. R., Paraschiv, A., Badea, T. A., Useriu, D., Frigioescu, T. F., Badea, G., & Cican, G. (2023). A Study on Mechanical Properties of Low-Cost Thermoplastic-Based Materials for Material Extrusion Additive Manufacturing. Polymers, 15(14), 2981. https://doi.org/10.3390/polym15142981

Vancouver

Condruz MR, Paraschiv A, Badea TA, Useriu D, Frigioescu TF, Badea G, et al. A Study on Mechanical Properties of Low-Cost Thermoplastic-Based Materials for Material Extrusion Additive Manufacturing. Polymers. 2023;15(14):2981. doi:10.3390/polym15142981

BibTeX
@article{Condruz2023,
  author = {Condruz, Mihaela-Raluca and Paraschiv, Alexandru and Badea, Teodor-Adrian and Useriu, Daniel and Frigioescu, Tiberius-Florian and Badea, Gabriel and Cican, Grigore},
  title = {A Study on Mechanical Properties of Low-Cost Thermoplastic-Based Materials for Material Extrusion Additive Manufacturing},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {14},
  pages = {2981},
  doi = {10.3390/polym15142981}
}
Kostenlos starten →