EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Fused Filament Fabricated Poly(lactic acid) Parts Reinforced with Short Carbon Fiber and Graphene Nanoparticles with Improved Tribological Properties

Anzum Al Abir iD, Dipto Chakrabarti, Bruno Trindade iD

Polymers · 25.05.2023 · 15 (11) · 2451

DOI: 10.3390/polym15112451 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 25.05.2023. Verfasst von Anzum Al Abir und 2 weiteren Autor:innen. Beteiligte Einrichtung: CEMMPRE-Centre for Mechanical Engineering, Materials and Processes, University of Coimbra, Rua Luís Reis Santos, 3030-788 Coimbra, Portugal. Die Arbeit wurde bisher 41-mal zitiert (Crossref) und nennt 48 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Fundação para a Ciência e Tecnologia, Portuguese Foundation for Science and Technology, Erasmus Mundus Scholarship.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study investigated the mechanical and tribological properties of 3D-printed Poly (lactic acid) (PLA) composites reinforced with different concentrations of carbon fibers (SCF) and graphene nanoparticles (GNP) (0.5 to 5 wt.% of each filler). The samples were produced using FFF (fused filament fabrication) 3D printing. The results showed a good dispersion of the fillers in the composites. SCF and GNP promoted the crystallization of the PLA filaments. The hardness, elastic modulus, and specific wear resistance grew with the increase in the filler concentration. A hardness improvement of about 30% was observed for the composite with 5 wt.% of SCF + 5 wt.% GNP (PSG-5) compared to PLA. The same trend was observed for the elastic modulus with an increase of 220%. All the composites presented lower coefficients of friction (0.49 to 0.6) than PLA (0.71). The composite PSG-5 sample showed the lowest value of specific wear rate (4.04 × 10−4 mm3/N.m), corresponding to about a five times reduction compared to PLA. Therefore, it was concluded that the addition of GNP and SCF to PLA made it possible to obtain composites with better mechanical and tribological behavior.

Schlagwörter

Stichwörter der Autor:innen

3D printingPLA compositegraphene nanoplateletsmechanical and tribological characterizationshort carbon fiber

Autor:innen und Institutionen

  • CEMMPRE-Centre for Mechanical Engineering, Materials and Processes, University of Coimbra, Rua Luís Reis Santos, 3030-788 Coimbra, Portugal.

ORCID-Profile: Anzum Al Abir, Bruno Trindade

Förderung

  • Fundação para a Ciência e Tecnologia
  • Portuguese Foundation for Science and Technology
  • Erasmus Mundus Scholarship
  • European Commission
  • EACEA agency

Zitieren

APA

Al Abir, A., Chakrabarti, D., & Trindade, B. (2023). Fused Filament Fabricated Poly(lactic acid) Parts Reinforced with Short Carbon Fiber and Graphene Nanoparticles with Improved Tribological Properties. Polymers, 15(11), 2451. https://doi.org/10.3390/polym15112451

Vancouver

Al Abir A, Chakrabarti D, Trindade B. Fused Filament Fabricated Poly(lactic acid) Parts Reinforced with Short Carbon Fiber and Graphene Nanoparticles with Improved Tribological Properties. Polymers. 2023;15(11):2451. doi:10.3390/polym15112451

BibTeX
@article{AlAbir2023,
  author = {Al Abir, Anzum and Chakrabarti, Dipto and Trindade, Bruno},
  title = {Fused Filament Fabricated Poly(lactic acid) Parts Reinforced with Short Carbon Fiber and Graphene Nanoparticles with Improved Tribological Properties},
  journal = {Polymers},
  year = {2023},
  volume = {15},
  number = {11},
  pages = {2451},
  doi = {10.3390/polym15112451}
}
Kostenlos starten →