Manufacture and Characterization of Polylactic Acid Filaments Recycled from Real Waste for 3D Printing
Polymers · 01.05.2023 · 15 (9) · 2165
DOI: 10.3390/polym15092165 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 01.05.2023. Verfasst von Saltanat Bergaliyeva und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Materials Science and Metallurgical Engineering and Inorganic Chemistry, Algeciras School of Engineering and Technology, Universidad de…. Die Arbeit wurde bisher 49-mal zitiert (Crossref) und nennt 56 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Regional Government of Andalusia, JUNTA DE ANDALUCíA, University of Cadiz’s Support.
Abstract (Originalsprache)
This paper studies the thermal, morphological, and mechanical properties of 3D-printed polylactic acid (PLA) blends of virgin and recycled material in the following proportions: 100/0, 25/75, 50/50, and 75/25, respectively. Real waste, used as recycled content, was shredded and sorted by size without a washing step. Regular dog-bone specimens were 3D printed from filaments, manufactured in a single screw extruder. Thermogravimetric analysis indicated that adding PLA debris to raw material did not significantly impact the thermal stability of the 3D-printed samples and showed that virgin and recycled PLA degraded at almost the same temperature. Differential scanning calorimetry revealed a significant reduction in crystallinity with increasing recycled content. Scanning electron microscopy showed a more homogenous structure for specimens from 100% pure PLA, as well as a more heterogeneous one for PLA blends. The tensile strength of the PLA blends increased by adding more recycled material, from 44.20 ± 2.18 MPa for primary PLA to 52.61 ± 2.28 MPa for the blend with the highest secondary PLA content. However, this study suggests that the mechanical properties of the reprocessed parts and their basic association are unique compared with those made up of virgin material.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Materials Science and Metallurgical Engineering and Inorganic Chemistry, Algeciras School of Engineering and Technology, Universidad de Cádiz, INNANOMAT, IMEYMAT, Ramón Puyol Ave, 11202 Algeciras, Cádiz, S…
- Physics and Technology Department, Al-Farabi Kazakh National University, 71, Al-Farabi Ave, Almaty 050040, Kazakhstan.
- Department of Materials Science and Metallurgical Engineering and Inorganic Chemistry, Universidad de Cádiz, Campus Río S. Pedro, INNANOMAT, IMEYMAT, 11510 Puerto Real, Cádiz, Spain.
ORCID-Profile: Saltanat Bergaliyeva, David L Sales, Sergio I Molina
Förderung
- Regional Government of Andalusia
- JUNTA DE ANDALUCíA
- University of Cadiz’s Support
- Stimulus Plan for Research and Transfer
- UE
- Hispano-Russian Centre of the University of Cádiz
Zitieren
APA
Bergaliyeva, S., Sales, D. L., Delgado, F. J., Bolegenova, S., & Molina, S. I. (2023). Manufacture and Characterization of Polylactic Acid Filaments Recycled from Real Waste for 3D Printing. Polymers, 15(9), 2165. https://doi.org/10.3390/polym15092165
Vancouver
Bergaliyeva S, Sales DL, Delgado FJ, Bolegenova S, Molina SI. Manufacture and Characterization of Polylactic Acid Filaments Recycled from Real Waste for 3D Printing. Polymers. 2023;15(9):2165. doi:10.3390/polym15092165
BibTeX
@article{Bergaliyeva2023,
author = {Bergaliyeva, Saltanat and Sales, David L and Delgado, Francisco J and Bolegenova, Saltanat and Molina, Sergio I},
title = {Manufacture and Characterization of Polylactic Acid Filaments Recycled from Real Waste for 3D Printing},
journal = {Polymers},
year = {2023},
volume = {15},
number = {9},
pages = {2165},
doi = {10.3390/polym15092165}
}
EUVIMED