Effect of Short Carbon Fiber Reinforcement on Mechanical Properties of 3D-Printed Acrylonitrile Butadiene Styrene
Polymers · 24.04.2023 · 15 (9) · 2011
DOI: 10.3390/polym15092011 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 24.04.2023. Verfasst von Evgeniy Lobov und 3 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Applied Mathematics and Mechanics, Perm National Research Polytechnic University, Perm 614990, Russia. Die Arbeit wurde bisher 40-mal zitiert (Crossref) und nennt 33 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Russian Science Foundation.
Abstract (Originalsprache)
The effect of short carbon fiber (SCF) filler on the mechanical properties of 3D-printed acrylonitrile butadiene styrene (ABS) was investigated. The fused filament fabrication (FFF) method was used for the manufacturing of samples. Elastic properties and strength characteristics of samples made of conventional ABS and SCF-reinforced ABS were compared in tensile and bending tests. Fracture toughness and critical strain energy release rate were also determined. In addition, 3D-printed monofilament SCF-reinforced samples were fabricated, the internal structure of which was analyzed using microcomputed tomography (micro-CT). Based on the tomography data, finite-element (FE) models of representative volume elements (RVEs) of the reinforced material were created and used for the numerical calculation of effective characteristics. Numerical and experimental results for the effective elastic properties were compared with the Mori-Tanaka homogenization technique. The ABS samples filled with SCF showed considerably higher mechanical characteristics than those of the conventional ABS. Finally, the dependence between the strength characteristics and elastic properties of the samples on the diameter of the nozzle used for 3D printing was established. 3D-printed ABS reinforced with SCF demonstrated a gain in tensile strength and fracture toughness by 30% and 20%, respectively. Interlayer adhesion strength in flexure tests showed an increase of 28% compared to pure ABS samples.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Faculty of Applied Mathematics and Mechanics, Perm National Research Polytechnic University, Perm 614990, Russia.
ORCID-Profile: Ilia Vindokurov, Mikhail Tashkinov
Förderung
- Russian Science Foundation
Zitieren
APA
Lobov, E., Dobrydneva, A., Vindokurov, I., & Tashkinov, M. (2023). Effect of Short Carbon Fiber Reinforcement on Mechanical Properties of 3D-Printed Acrylonitrile Butadiene Styrene. Polymers, 15(9), 2011. https://doi.org/10.3390/polym15092011
Vancouver
Lobov E, Dobrydneva A, Vindokurov I, Tashkinov M. Effect of Short Carbon Fiber Reinforcement on Mechanical Properties of 3D-Printed Acrylonitrile Butadiene Styrene. Polymers. 2023;15(9):2011. doi:10.3390/polym15092011
BibTeX
@article{Lobov2023,
author = {Lobov, Evgeniy and Dobrydneva, Anastasia and Vindokurov, Ilia and Tashkinov, Mikhail},
title = {Effect of Short Carbon Fiber Reinforcement on Mechanical Properties of 3D-Printed Acrylonitrile Butadiene Styrene},
journal = {Polymers},
year = {2023},
volume = {15},
number = {9},
pages = {2011},
doi = {10.3390/polym15092011}
}
EUVIMED