Selective Laser Sintering 3D Printing of Carvedilol Tablets: Enhancing Dissolution Through Amorphization
Pharmaceutics · 24.12.2024 · 17 (1) · 6
DOI: 10.3390/pharmaceutics17010006 ↗Kurz gefasst
Fachartikel in der Zeitschrift Pharmaceutics, online erschienen am 24.12.2024. Verfasst von Nikola Pešić und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Pharmaceutical Technology and Cosmetology, Faculty of Pharmacy, University of Belgrade, Vojvode Stepe 450, 11221 Belgrade, Serbia. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 43 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Science, Technological Development and Innovation, Republic of Serbia, Ministry of Science, Technological Development and Innovation, Republic of Serbia through two Grant Agreements with the University of Belgrade’s Faculty of Pha….
Abstract (Originalsprache)
Background/Objectives: Selective laser sintering (SLS) is one of the most promising 3D printing techniques for pharmaceutical applications as it offers numerous advantages, such as suitability to work with already approved pharmaceutical excipients, the elimination of solvents, and the ability to produce fast-dissolving, porous dosage forms with high drug loading. When the powder mixture is exposed to elevated temperatures during SLS printing, the active ingredients can be converted from the crystalline to the amorphous state, which can be used as a strategy to improve the dissolution rate and bioavailability of poorly soluble drugs. This study investigates the potential application of SLS 3D printing for the fabrication of tablets containing the poorly soluble drug carvedilol with the aim of improving the dissolution rate of the drug by forming an amorphous form through the printing process.
Methods
Using SLS 3D printing, eight tablet formulations were produced using two different powder mixtures and four combinations of experimental conditions, followed by physicochemical characterization and dissolution testing.
Results
Physicochemical characterization revealed that at least partial amorphization of carvedilol occurred during the printing process. Although variations in process parameters were minimal, higher temperatures in combination with lower laser speeds appeared to facilitate a greater degree of amorphization. Ultimately, the partial conversion to the amorphous form significantly improved the dissolution of carvedilol compared to its pure crystalline form.
Conclusions
Obtained results suggest that the SLS 3D printing technique can be effectively used to convert poorly water-soluble drugs to their amorphous state, thereby improving solubility and bioavailability.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Pharmaceutical Technology and Cosmetology, Faculty of Pharmacy, University of Belgrade, Vojvode Stepe 450, 11221 Belgrade, Serbia.
- Department of Pharmaceutical Chemistry, Faculty of Pharmacy, University of Belgrade, Vojvode Stepe 450, 11221 Belgrade, Serbia.
- Vinča Institute of Nuclear Sciences, National Institute of the Republic of Serbia, University of Belgrade, Mike Petrovića Alasa 12-14, 11351 Belgrade, Serbia.
- Galenika a.d., Batajnički drum bb., 11080 Belgrade, Serbia.
ORCID-Profile: Tanja Barudžija, Svetlana Ibrić
Förderung
- Ministry of Science, Technological Development and Innovation, Republic of Serbia
- Ministry of Science, Technological Development and Innovation, Republic of Serbia through two Grant Agreements with the University of Belgrade’s Faculty of Pha…
Zitieren
APA
Pešić, N., Ivković, B., Barudžija, T., Grujić, B., Ibrić, S., & Medarević, D. (2024). Selective Laser Sintering 3D Printing of Carvedilol Tablets: Enhancing Dissolution Through Amorphization. Pharmaceutics, 17(1), 6. https://doi.org/10.3390/pharmaceutics17010006
Vancouver
Pešić N, Ivković B, Barudžija T, Grujić B, Ibrić S, Medarević D. Selective Laser Sintering 3D Printing of Carvedilol Tablets: Enhancing Dissolution Through Amorphization. Pharmaceutics. 2024;17(1):6. doi:10.3390/pharmaceutics17010006
BibTeX
@article{Pei2024,
author = {Pešić, Nikola and Ivković, Branka and Barudžija, Tanja and Grujić, Branka and Ibrić, Svetlana and Medarević, Djordje},
title = {Selective Laser Sintering 3D Printing of Carvedilol Tablets: Enhancing Dissolution Through Amorphization},
journal = {Pharmaceutics},
year = {2024},
volume = {17},
number = {1},
pages = {6},
doi = {10.3390/pharmaceutics17010006}
}
EUVIMED