EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Role of Selected Organic Additives in Sulfate-Based Electroplating Baths for Copper Electrodeposition Toward Additive Manufacturing

Dawid Kiesiewicz iD, Karolina Syrek iD, Paweł Niezgoda, Maciej Pilch

Molecules · 13.05.2026 · 31 (10) · 1635

DOI: 10.3390/molecules31101635 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Molecules, online erschienen am 13.05.2026. Verfasst von Dawid Kiesiewicz und 3 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Civil Engineering, Cracow University of Technology, Warszawska 24, 31-155 Cracow, Poland. Die Arbeit nennt 46 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Centre for Research and Development.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Precise control of copper electrodeposition is essential for electrochemical additive manufacturing based on layer-by-layer growth. In this work, the influence of selected organic additives, nicotinic acid, benzotriazole, thiourea and urea in sulfate-based electroplating baths was investigated with respect to their applicability in electrodeposition-driven 3D printing. Linear sweep voltammetry (LSV) was used to analyze the electrochemical behavior of Cu(II) reduction, while copper layers were deposited under potentiostatic conditions in a flow-assisted system (potential controlled conditions). The obtained deposits were characterized by SEM/EDS and quantitative measurements of layer thickness and dendrite height. The results show that the additives strongly affect both deposition kinetics and the morphology of electrodeposited layers. Benzotriazole acts as a strong inhibitor, producing fine-grained structures but reducing deposition efficiency and not fully suppressing vertical growth instabilities. Thiourea leads to highly unstable deposition with excessive dendritic growth and increased impurity incorporation. Nicotinic acid enables relatively thick deposits with moderate dendrite formation within an optimal concentration range. In contrast, urea provides the most stable growth, yielding uniform layers with minimal dendritic development and high copper purity. The dendrite height-to-layer thickness ratio proved to be an effective descriptor of electrodeposition growth stability. These findings highlight the critical role of additive selection in optimizing electroplating baths for electrochemical 3D printing applications.

Schlagwörter

Stichwörter der Autor:innen

additive manufacturingcopper electrodepositionorganic additivessulfate-based electroplating baths

Autor:innen und Institutionen

  • Faculty of Civil Engineering, Cracow University of Technology, Warszawska 24, 31-155 Cracow, Poland.
  • Faculty of Chemistry, Jagiellonian University, Gronostajowa 2, 30-387 Cracow, Poland.
  • Faculty of Chemical Engineering and Technology, Cracow University of Technology, Warszawska 24, 31-155 Cracow, Poland.

ORCID-Profile: Dawid Kiesiewicz, Karolina Syrek

Förderung

  • National Centre for Research and Development

Zitieren

APA

Kiesiewicz, D., Syrek, K., Niezgoda, P., & Pilch, M. (2026). Role of Selected Organic Additives in Sulfate-Based Electroplating Baths for Copper Electrodeposition Toward Additive Manufacturing. Molecules, 31(10), 1635. https://doi.org/10.3390/molecules31101635

Vancouver

Kiesiewicz D, Syrek K, Niezgoda P, Pilch M. Role of Selected Organic Additives in Sulfate-Based Electroplating Baths for Copper Electrodeposition Toward Additive Manufacturing. Molecules. 2026;31(10):1635. doi:10.3390/molecules31101635

BibTeX
@article{Kiesiewicz2026,
  author = {Kiesiewicz, Dawid and Syrek, Karolina and Niezgoda, Paweł and Pilch, Maciej},
  title = {Role of Selected Organic Additives in Sulfate-Based Electroplating Baths for Copper Electrodeposition Toward Additive Manufacturing},
  journal = {Molecules},
  year = {2026},
  volume = {31},
  number = {10},
  pages = {1635},
  doi = {10.3390/molecules31101635}
}
Kostenlos starten →