Surface Topography Improvement of Micro-Milled Inconel 718 Slots Through Abrasive Deburring: Comparison Between Polishing and Sanding
Micromachines · 11.08.2026 · 17 (8) · 951
DOI: 10.3390/mi17080951 ↗Kurz gefasst
Fachartikel in der Zeitschrift Micromachines, online erschienen am 11.08.2026. Verfasst von Gabriel de Paiva Silva und 4 weiteren Autor:innen. Beteiligte Einrichtung: École Nationale Supérieure d'Arts et Métiers, LAMPA, 2 Bd du Ronceray, 49035 Angers, France. Die Arbeit nennt 49 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Universidade de Brasília, Coordenação de Aperfeicoamento de Pessoal de Nível Superior, Foundation for Research Support of the Federal District.
Abstract (Originalsprache)
Burr formation remains a major challenge in micro milling due to reduced tool dimensions and size-effect phenomena, particularly when machining difficult-to-cut materials such as Inconel 718. This study compares the effectiveness of two abrasive deburring processes, polishing and sanding, applied to micro-milled slots, focusing on burr removal and surface topography modification. Twelve 15 mm long slots were machined using a 400 µm diameter TiAlN-coated micro end mill under constant cutting conditions. Deburring was performed for 1, 2, and 4 min for polishing and for 30 s for sanding. Surface topography and burr height were evaluated before and after each process. The results revealed significant burr formation, with burr heights reaching the same order of magnitude as the axial depth of cut and higher values on the down-milling side. Polishing showed limited deburring capability, primarily promoting burr deformation while reducing surface roughness by up to 21%. In contrast, sanding reduced total height of the burrs by up to 99% and generated flatter edge morphologies, although surface roughness increased by up to 19%. These findings highlight the trade-off between burr control and surface quality in the abrasive post-processing of micro-milled Inconel 718 features.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- École Nationale Supérieure d'Arts et Métiers, LAMPA, 2 Bd du Ronceray, 49035 Angers, France.
- Department of Mechanical Engineering, University of Brasilia, Asa Norte, Brasília 70910-900, DF, Brazil.
- School of Mechanical Engineering, Federal University of Piauí, Ministro Petrônio Portella Campus, Ininga, Teresina 64049-550, PI, Brazil.
ORCID-Profile: Raphael Lima de Paiva, Maksym Ziberov, Déborah de Oliveira
Förderung
- Universidade de Brasília
- Coordenação de Aperfeicoamento de Pessoal de Nível Superior
- Foundation for Research Support of the Federal District
- Conselho Nacional de Desenvolvimento Científico e Tecnológico
- CNPq
Zitieren
APA
Silva, G. P., Araujo, M. L., de Paiva, R. L., Ziberov, M., & de Oliveira, D. (2026). Surface Topography Improvement of Micro-Milled Inconel 718 Slots Through Abrasive Deburring: Comparison Between Polishing and Sanding. Micromachines, 17(8), 951. https://doi.org/10.3390/mi17080951
Vancouver
Silva GP, Araujo ML, de Paiva RL, Ziberov M, de Oliveira D. Surface Topography Improvement of Micro-Milled Inconel 718 Slots Through Abrasive Deburring: Comparison Between Polishing and Sanding. Micromachines. 2026;17(8):951. doi:10.3390/mi17080951
BibTeX
@article{Silva2026,
author = {Silva, Gabriel de Paiva and Araujo, Marcelo Lopes and de Paiva, Raphael Lima and Ziberov, Maksym and de Oliveira, Déborah},
title = {Surface Topography Improvement of Micro-Milled Inconel 718 Slots Through Abrasive Deburring: Comparison Between Polishing and Sanding},
journal = {Micromachines},
year = {2026},
volume = {17},
number = {8},
pages = {951},
doi = {10.3390/mi17080951}
}
EUVIMED