EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Modeling and Error Compensation for Concentric Grinding of Spherical Surfaces

Baozhen Li, Keyan Song, Dongxu Wu, Lin Sun iD, Yunfei Li

Micromachines · 05.07.2026 · 17 (7) · 812

DOI: 10.3390/mi17070812 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Micromachines, online erschienen am 05.07.2026. Verfasst von Baozhen Li und 4 weiteren Autor:innen. Beteiligte Einrichtung: Genertec Machine Tool Engineering Research Institute Co., Ltd., Beijing 100102, China. Die Arbeit nennt 24 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Aeronautical Science Foundation of China, the Major Science and Technology Project of the GENERTEC.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

To improve the form accuracy of spherical surfaces generated by cup-wheel grinding, this paper presents a geometric modeling and error compensation method for concentric grinding of spherical surfaces. A cup-shaped arc grinding wheel, hereafter referred to as a cup wheel, is used as the grinding tool. The relative motion between the cup wheel and the workpiece is formulated so that the contact arc center of the wheel follows a trajectory that is concentric with the target spherical surface. Based on this principle, trajectory models for both convex and concave spherical surfaces are established, and the geometric constraints for cup-wheel dimension selection are analyzed. To compensate for tool-setting errors and wheel-wear-induced deviations, a central-peak-based error compensation model is further developed. Grinding experiments on a convex spherical sample were conducted to verify the proposed trajectory and compensation models. The results show that the form error PV value was reduced from 57.7 μm to 0.3 μm after compensation, demonstrating the effectiveness of the proposed model in improving spherical form accuracy.

Schlagwörter

Stichwörter der Autor:innen

grinding wheeloptical componentsspherical surfaceultra-precision grinding

Autor:innen und Institutionen

  • Genertec Machine Tool Engineering Research Institute Co., Ltd., Beijing 100102, China.
  • Genertec Joint Research Institute, Xi'an Jiaotong University, Xi'an 710049, China.
  • School of Mechanical Engineering, Xi'an Jiaotong University, Xi'an 710049, China.

ORCID-Profile: Lin Sun

Förderung

  • National Natural Science Foundation of China
  • Aeronautical Science Foundation of China
  • the Major Science and Technology Project of the GENERTEC
  • Shaanxi Provincial Key R&D Program Projects

Zitieren

APA

Li, B., Song, K., Wu, D., Sun, L., & Li, Y. (2026). Modeling and Error Compensation for Concentric Grinding of Spherical Surfaces. Micromachines, 17(7), 812. https://doi.org/10.3390/mi17070812

Vancouver

Li B, Song K, Wu D, Sun L, Li Y. Modeling and Error Compensation for Concentric Grinding of Spherical Surfaces. Micromachines. 2026;17(7):812. doi:10.3390/mi17070812

BibTeX
@article{Li2026,
  author = {Li, Baozhen and Song, Keyan and Wu, Dongxu and Sun, Lin and Li, Yunfei},
  title = {Modeling and Error Compensation for Concentric Grinding of Spherical Surfaces},
  journal = {Micromachines},
  year = {2026},
  volume = {17},
  number = {7},
  pages = {812},
  doi = {10.3390/mi17070812}
}
Kostenlos starten →