Effects of In Situ Preheating Technology on Mechanical Properties and Microstructure of FFF-Printed PEEK
Micromachines · 28.02.2026 · 17 (3) · 303
DOI: 10.3390/mi17030303 ↗Kurz gefasst
Fachartikel in der Zeitschrift Micromachines, online erschienen am 28.02.2026. Verfasst von Junhua Wang und 8 weiteren Autor:innen. Beteiligte Einrichtung: School of Mechanical and Electrical Engineering, Henan University of Science and Technology, Luoyang 471003, China. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 38 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: the Postdoctoral Fellowship Program of CPSF, the China Postdoctoral Science Foundation under, Key Scientific Research Projects of Colleges and Universities in Henan Province.
Abstract (Originalsprache)
The Polyether ether ketone (PEEK) suffers from insufficient interlayer molecular chain diffusion and weak interfacial fusion during Fused Filament Fabrication (FFF) due to its high melt viscosity and rapid cooling characteristics, restricting the mechanical properties and engineering applications of printed parts. To improve the interlayer bonding quality of FFF-printed PEEK, an in situ preheating technology integrated into the print nozzle was proposed and implemented. Through a high-temperature controllable preheating system that moves synchronously with the nozzle, local precise heating is performed on the surface of the deposited layer to actively regulate the thermal history of the interlayer interface. Systematic studies on the effect of preheating temperature were conducted. The results show that the influence of preheating temperature on part performance follows a trend of first increasing and then decreasing. When the preheating temperature is 280 °C, the comprehensive performance of the specimens is optimal: the tensile strength reaches 69.47 MPa, which is 21.3% higher than that of the non-preheated reference group; the elongation at break is 71.07%; and the porosity decreases to 8.36%. Microstructural analysis reveals that moderate preheating facilitates molecular chain diffusion and interfacial fusion, whereas excessive heating induces thermal oxidative degradation of PEEK, resulting in deteriorated mechanical performance. These findings confirm that in situ preheating represents an effective approach for enhancing interlayer bonding, thereby offering a practical solution for the additive manufacturing of high-performance PEEK components.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- School of Mechanical and Electrical Engineering, Henan University of Science and Technology, Luoyang 471003, China.
- Henan Intelligent Manufacturing Equipment Engineering Technology Research Center, Luoyang 471003, China.
- Henan Engineering Laboratory of Intelligent Numerical Control Equipment, Luoyang 471003, China.
- School of Materials Science and Engineering, Henan University of Science and Technology, Luoyang 471023, China.
- State Key Laboratory of Mechanical Transmission for Advanced Equipment, College of Mechanical and Vehicle Engineering, Chongqing University, Chongqing 400044, China.
- College of Mechanical and Vehicle Engineering, Chongqing University, Chongqing 400044, China.
ORCID-Profile: Junhua Wang, Kun Li
Förderung
- the Postdoctoral Fellowship Program of CPSF
- the China Postdoctoral Science Foundation under
- Key Scientific Research Projects of Colleges and Universities in Henan Province
- Henan Provincial Department of Science and Technology
- Key R&D Program of Henan Province
- Tribology Science Fund of State Key Laboratory of Tribology in Advanced Equipment
- Postdoctoral Fellowship Program of CPSF
- China Postdoctoral ScienceFoundation
Zitieren
APA
Wang, J., Mao, Y., Shen, J., Lu, Y., Li, K., Xu, J., Zhang, Z., Gu, R., & Xie, T. (2026). Effects of In Situ Preheating Technology on Mechanical Properties and Microstructure of FFF-Printed PEEK. Micromachines, 17(3), 303. https://doi.org/10.3390/mi17030303
Vancouver
Wang J, Mao Y, Shen J, Lu Y, Li K, Xu J, et al. Effects of In Situ Preheating Technology on Mechanical Properties and Microstructure of FFF-Printed PEEK. Micromachines. 2026;17(3):303. doi:10.3390/mi17030303
BibTeX
@article{Wang2026,
author = {Wang, Junhua and Mao, Yuanming and Shen, Jianan and Lu, Yan and Li, Kun and Xu, Junfei and Zhang, Zhuangya and Gu, Ruijie and Xie, Tancheng},
title = {Effects of In Situ Preheating Technology on Mechanical Properties and Microstructure of FFF-Printed PEEK},
journal = {Micromachines},
year = {2026},
volume = {17},
number = {3},
pages = {303},
doi = {10.3390/mi17030303}
}
EUVIMED