EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Multi-Objective Optimization of Surface Roughness, Cutting Force, and Temperature in Ultrasonic-Vibration-Assisted Milling of Titanium Alloy

Gaofeng Hu, Yanjie Lu, Shengming Zhou, Xin He iD, Fenghui Zhang, Pengchao Zhu, Mingshang Wang, Taowei Tan, Guangjun Chen

Micromachines · 14.08.2025 · 16 (8) · 936

DOI: 10.3390/mi16080936 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Micromachines, online erschienen am 14.08.2025. Verfasst von Gaofeng Hu und 8 weiteren Autor:innen. Beteiligte Einrichtung: College of Mechanical Engineering, Tianjin University of Technology and Education, Tianjin 300222, China. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 30 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Tianjin Science and Technology Plan Project, Open Project of Key Laboratory of High-end CNC Machine Tool of Genertec, Tianjin Education Commission Project.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Titanium alloys (Ti-6Al-4V) are widely used in the aerospace field. However, as a typical difficult-to-machine material, titanium alloys have a low thermal conductivity, a high chemical activity, and a significant adiabatic shear effect. In conventional milling (CM), the temperature in the cutting zone rises sharply, leading to tool adhesion, rapid wear, and damage to the workpiece surface. This article systematically investigated the influence of process parameters on the surface roughness, cutting force, and cutting temperature in the ultrasonic-vibration-assisted milling (UAM) process of titanium alloys, based on which multi-objective optimization process of the milling process parameters was conducted, by utilizing the grey relational analysis method. An orthogonal experiment with four factors and four levels was conducted. The effects of various process parameters on the surface roughness, cutting force, and cutting temperature were systematically analyzed for both UAM and CM. The grey relational analysis method was employed to transform the optimization problem of multiple process target parameters into a single-objective grey relational degree optimization problem. The optimized parameter combination was as follows: an ultrasonic amplitude of 6 μm, a spindle speed of 6000 rpm, a cutting depth of 0.20 mm, and a feed rate of 200 mm/min. The experimental results indicated that the surface roughness Sa was 0.268 μm, the cutting temperature was 255.39 °C, the cutting force in the X direction (FX) was 5.2 N, the cutting force in the Y direction (FY) was 7.9 N, and the cutting force in the Z direction (FZ) was 6.4 N. The optimization scheme significantly improved the machining quality and reduced both the cutting forces and the cutting temperature.

Schlagwörter

Stichwörter der Autor:innen

cutting forcecutting temperaturemulti-objective optimizationsurface roughnessultrasonic-vibration-assisted milling

Autor:innen und Institutionen

  • College of Mechanical Engineering, Tianjin University of Technology and Education, Tianjin 300222, China.
  • Tianjin Key Laboratory of High Performance Manufacturing Technology & Equipment, Tianjin 300222, China.
  • College of Mechanical Engineering, Tianjin University, Tianjin 300222, China.
  • Engineering Training Center, Tianjin University of Technology and Education, Tianjin 300222, China.

ORCID-Profile: Xin He

Förderung

  • Tianjin Science and Technology Plan Project
  • Open Project of Key Laboratory of High-end CNC Machine Tool of Genertec
  • Tianjin Education Commission Project
  • Scientific Research Program Project of Tianjin University of Technology and Education

Zitieren

APA

Hu, G., Lu, Y., Zhou, S., He, X., Zhang, F., Zhu, P., Wang, M., Tan, T., & Chen, G. (2025). Multi-Objective Optimization of Surface Roughness, Cutting Force, and Temperature in Ultrasonic-Vibration-Assisted Milling of Titanium Alloy. Micromachines, 16(8), 936. https://doi.org/10.3390/mi16080936

Vancouver

Hu G, Lu Y, Zhou S, He X, Zhang F, Zhu P, et al. Multi-Objective Optimization of Surface Roughness, Cutting Force, and Temperature in Ultrasonic-Vibration-Assisted Milling of Titanium Alloy. Micromachines. 2025;16(8):936. doi:10.3390/mi16080936

BibTeX
@article{Hu2025,
  author = {Hu, Gaofeng and Lu, Yanjie and Zhou, Shengming and He, Xin and Zhang, Fenghui and Zhu, Pengchao and Wang, Mingshang and Tan, Taowei and Chen, Guangjun},
  title = {Multi-Objective Optimization of Surface Roughness, Cutting Force, and Temperature in Ultrasonic-Vibration-Assisted Milling of Titanium Alloy},
  journal = {Micromachines},
  year = {2025},
  volume = {16},
  number = {8},
  pages = {936},
  doi = {10.3390/mi16080936}
}
Kostenlos starten →