EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Rapid Micromolding of Sub-100 µm Microfluidic Channels Using an 8K Stereolithographic Resin 3D Printer

Arpith Vedhanayagam, Michael Golfetto, Jeffrey L Ram, Amar S Basu iD

Micromachines · 28.07.2023 · 14 (8) · 1519

DOI: 10.3390/mi14081519 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Micromachines, online erschienen am 28.07.2023. Verfasst von Arpith Vedhanayagam und 3 weiteren Autor:innen. Beteiligte Einrichtung: Electrical and Computer Engineering, Wayne State University, Detroit, MI 48202, USA. Die Arbeit wurde bisher 30-mal zitiert (Crossref) und nennt 50 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Great Lakes Protection Fund, Wayne State University, Great Lakes Water Authority (GLWA).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Engineering microfluidic devices relies on the ability to manufacture sub-100 micrometer fluidic channels. Conventional lithographic methods provide high resolution but require costly exposure tools and outsourcing of masks, which extends the turnaround time to several days. The desire to accelerate design/test cycles has motivated the rapid prototyping of microfluidic channels; however, many of these methods (e.g., laser cutters, craft cutters, fused deposition modeling) have feature sizes of several hundred microns or more. In this paper, we describe a 1-day process for fabricating sub-100 µm channels, leveraging a low-cost (USD 600) 8K digital light projection (DLP) 3D resin printer. The soft lithography process includes mold printing, post-treatment, and casting polydimethylsiloxane (PDMS) elastomer. The process can produce microchannels with 44 µm lateral resolution and 25 µm height, posts as small as 400 µm, aspect ratio up to 7, structures with varying z-height, integrated reservoirs for fluidic connections, and a built-in tray for casting. We discuss strategies to obtain reliable structures, prevent mold warpage, facilitate curing and removal of PDMS during molding, and recycle the solvents used in the process. To our knowledge, this is the first low-cost 3D printer that prints extruded structures that can mold sub-100 µm channels, providing a balance between resolution, turnaround time, and cost (~USD 5 for a 2 × 5 × 0.5 cm3 chip) that will be attractive for many microfluidics labs.

Schlagwörter

Stichwörter der Autor:innen

3D resin printingPDMS soft lithographymicromoldingrapid prototyping

Autor:innen und Institutionen

  • Electrical and Computer Engineering, Wayne State University, Detroit, MI 48202, USA.
  • Department of Physiology, Wayne State University School of Medicine, Detroit, MI 48201, USA.

ORCID-Profile: Amar S Basu

Förderung

  • Great Lakes Protection Fund
  • Wayne State University
  • Great Lakes Water Authority (GLWA)
  • National Science Foundation (NSF) award
  • Wayne State University OneHealth Initiative

Zitieren

APA

Vedhanayagam, A., Golfetto, M., Ram, J. L., & Basu, A. S. (2023). Rapid Micromolding of Sub-100 µm Microfluidic Channels Using an 8K Stereolithographic Resin 3D Printer. Micromachines, 14(8), 1519. https://doi.org/10.3390/mi14081519

Vancouver

Vedhanayagam A, Golfetto M, Ram JL, Basu AS. Rapid Micromolding of Sub-100 µm Microfluidic Channels Using an 8K Stereolithographic Resin 3D Printer. Micromachines. 2023;14(8):1519. doi:10.3390/mi14081519

BibTeX
@article{Vedhanayagam2023,
  author = {Vedhanayagam, Arpith and Golfetto, Michael and Ram, Jeffrey L and Basu, Amar S},
  title = {Rapid Micromolding of Sub-100 µm Microfluidic Channels Using an 8K Stereolithographic Resin 3D Printer},
  journal = {Micromachines},
  year = {2023},
  volume = {14},
  number = {8},
  pages = {1519},
  doi = {10.3390/mi14081519}
}
Kostenlos starten →