EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Milling Stability Prediction: A New Approach Based on a Composited Newton–Cotes Formula

Junqiang Zheng iD, Pengfei Ren, Chaofeng Zhou, Xu Du

Micromachines · 25.06.2023 · 14 (7) · 1304

DOI: 10.3390/mi14071304 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Micromachines, online erschienen am 25.06.2023. Verfasst von Junqiang Zheng und 3 weiteren Autor:innen. Beteiligte Einrichtung: School of Mechanical Engineering, Hefei University of Technology, Hefei 230009, China. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 34 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Zhejiang Provincial Natural Science Foundation, National Natural Science Foundation of China, Natural Science Foundation of Zhejiang Province.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Based on a composited Newton–Cotes formula, this paper proposes a numerical method to predict milling stability considering regenerative chatter and focusing on rate and prediction accuracy. First, the dynamic model of milling motion is expressed as state-space equations considering regenerative chatter, with the tooth passing period divided into a set of time intervals. Second, a composited Newton–Cotes formula is introduced to calculate the transition function map for each time interval. Third, the state transition matrix is constructed based on the above-mentioned transition function, and the prediction stability boundary is determined by the Floquet theory. Finally, simulation analysis and experimental verification are conducted to verify the effectiveness of the proposed method. The simulation results demonstrate that, for the milling model with a single degree of freedom (DOF), the convergence rate and prediction accuracy of the proposed method are higher than those of the comparison method. The experimental results demonstrate that, for the milling model with two DOFs, the machining parameters below the prediction stability boundary can avoid the chatter as much as possible, ensuring the machined surface quality.

Schlagwörter

Stichwörter der Autor:innen

Floquet theorycomposite cotes formuladynamic modelmilling stability predictionregenerative chatter

Autor:innen und Institutionen

  • School of Mechanical Engineering, Hefei University of Technology, Hefei 230009, China.
  • School of Mechanical Engineering, Hangzhou Dianzi University, Hangzhou 310018, China.
  • School of Mechanical Engineering, Zhejiang Sci-Tech University, Hangzhou 310018, China.

ORCID-Profile: Junqiang Zheng

Förderung

  • Zhejiang Provincial Natural Science Foundation
  • National Natural Science Foundation of China
  • Natural Science Foundation of Zhejiang Province
  • Postdoctoral research activities of Anhui Province

Zitieren

APA

Zheng, J., Ren, P., Zhou, C., & Du, X. (2023). Milling Stability Prediction: A New Approach Based on a Composited Newton–Cotes Formula. Micromachines, 14(7), 1304. https://doi.org/10.3390/mi14071304

Vancouver

Zheng J, Ren P, Zhou C, Du X. Milling Stability Prediction: A New Approach Based on a Composited Newton–Cotes Formula. Micromachines. 2023;14(7):1304. doi:10.3390/mi14071304

BibTeX
@article{Zheng2023,
  author = {Zheng, Junqiang and Ren, Pengfei and Zhou, Chaofeng and Du, Xu},
  title = {Milling Stability Prediction: A New Approach Based on a Composited Newton–Cotes Formula},
  journal = {Micromachines},
  year = {2023},
  volume = {14},
  number = {7},
  pages = {1304},
  doi = {10.3390/mi14071304}
}
Kostenlos starten →