EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

The Effect of 3D Printing Tilt Angle on the Penetration of 3D-Printed Microneedle Arrays

Mahmood Razzaghi iD, Mohsen Akbari iD

Micromachines · 30.05.2023 · 14 (6) · 1157

DOI: 10.3390/mi14061157 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Micromachines, online erschienen am 30.05.2023. Verfasst von Mahmood Razzaghi und 1 weiteren Autor:innen. Beteiligte Einrichtung: Laboratory for Innovations in Microengineering (LiME), Department of Mechanical Engineering, University of Victoria, Victoria, BC V8P 5C2, Canada. Die Arbeit wurde bisher 32-mal zitiert (Crossref) und nennt 46 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Natural Sciences and Engineering Research Council of Canada (NSERC), Canadian Institutes for Health Research (CIHR), Canadian Foundation for Innovation (CFI).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Microneedle arrays (MNAs) are emerging devices that are mainly used for drug delivery and diagnostic applications through the skin. Different methods have been used to fabricate MNAs. Recently developed fabrication methods based on 3D printing have many advantages compared to conventional fabrication methods, such as faster fabrication in one step and the ability to fabricate complex structures with precise control over their geometry, form, size, and mechanical and biological properties. Despite the several advantages that 3D printing offers for the fabrication of microneedles, their poor penetration capability into the skin should be improved. MNAs need a sharp needle tip to penetrate the skin barrier layer, the stratum corneum (SC). This article presents a method to improve the penetration of 3D-printed microneedle arrays by investigating the effect of the printing angle on the penetration force of MNAs. The penetration force needed to puncture the skin for MNAs fabricated using a commercial digital light processing (DLP) printer, with different printing tilt angles (0–60°), was measured in this study. The results showed that the minimum puncture force was achieved using a 45° printing tilt angle. Using this angle, the puncture force was reduced by 38% compared to MNAs printed with a tilting angle of 0°. We also identified that a tip angle of 120° resulted in the smallest penetration force needed to puncture the skin. The outcomes of the research show that the presented method can significantly improve the penetration capability of 3D-printed MNAs into the skin.

Schlagwörter

Stichwörter der Autor:innen

3D printingmicroneedlemicroneedle arraypenetrationtilting angle

Autor:innen und Institutionen

  • Laboratory for Innovations in Microengineering (LiME), Department of Mechanical Engineering, University of Victoria, Victoria, BC V8P 5C2, Canada.
  • Terasaki Institute for Biomedical Innovations, Los Angeles, CA 90050, USA.
  • Biotechnology Center, Silesian University of Technology, Akademicka 2A, 44-100 Gliwice, Poland.

ORCID-Profile: Mahmood Razzaghi, Mohsen Akbari

Förderung

  • Natural Sciences and Engineering Research Council of Canada (NSERC)
  • Canadian Institutes for Health Research (CIHR)
  • Canadian Foundation for Innovation (CFI)

Zitieren

APA

Razzaghi, M., & Akbari, M. (2023). The Effect of 3D Printing Tilt Angle on the Penetration of 3D-Printed Microneedle Arrays. Micromachines, 14(6), 1157. https://doi.org/10.3390/mi14061157

Vancouver

Razzaghi M, Akbari M. The Effect of 3D Printing Tilt Angle on the Penetration of 3D-Printed Microneedle Arrays. Micromachines. 2023;14(6):1157. doi:10.3390/mi14061157

BibTeX
@article{Razzaghi2023,
  author = {Razzaghi, Mahmood and Akbari, Mohsen},
  title = {The Effect of 3D Printing Tilt Angle on the Penetration of 3D-Printed Microneedle Arrays},
  journal = {Micromachines},
  year = {2023},
  volume = {14},
  number = {6},
  pages = {1157},
  doi = {10.3390/mi14061157}
}
Kostenlos starten →