EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Study of Gas Film Characteristics in Electrochemical Discharge Machining and Their Effects on Discharge Energy Distribution

Hao Liu iD, Adayi Xieeryazidan

Micromachines · 20.05.2023 · 14 (5) · 1079

DOI: 10.3390/mi14051079 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Micromachines, online erschienen am 20.05.2023. Verfasst von Hao Liu und 1 weiteren Autor:innen. Beteiligte Einrichtung: School of Mechanical Engineering, Xinjiang University, Urumqi 830017, China. Die Arbeit wurde bisher 17-mal zitiert (Crossref) und nennt 21 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Adayi Xieeryazidan, National Natural Science Foundation of China.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Glass is a hard and brittle insulating material that is widely used in optics, biomedicine, and microelectromechanical systems. The electrochemical discharge process, which involves an effective microfabrication technology for insulating hard and brittle materials, can be used to perform effective microstructural processing on glass. The gas film is the most important medium in this process, and its quality is an important factor in the formation of good surface microstructures. This study focuses on the gas film properties and their influence on the discharge energy distribution. In this study, a complete factorial design of experiments (DOE) was used, with three factors and three levels of voltage, duty cycle, and frequency as the influencing factors and gas film thickness as the response for the experimental study, to obtain the best combination of process parameters that would result in the best gas film quality. In addition, experiments and simulations of microhole processing on two types of glass, quartz glass and K9 optical glass, were conducted for the first time to characterize the discharge energy distribution of the gas film based on the radial overcut, depth-to-diameter ratio, and roundness error, and to analyze the gas film characteristics and their effects on the discharge energy distribution. The experimental results demonstrated the optimal combination of process parameters, at a voltage of 50 V, a frequency of 20 kHz and a duty cycle of 80%, that achieved a better gas film quality and a more uniform discharge energy distribution. A thin and stable gas film with a thickness of 189 μm was obtained with the optimal combination of parameters, which was 149 μm less than the extreme combination of parameters (60 V, 25 kHz, 60%). These studies resulted in an 81 μm reduction in radial overcut, a roundness error reduced by 14, and a 49% increase in the depth–shallow ratio for a microhole machined on quartz glass.

Schlagwörter

Stichwörter der Autor:innen

ECDMdischarge energy distributiongas film characterizationmachining quality

Autor:innen und Institutionen

  • School of Mechanical Engineering, Xinjiang University, Urumqi 830017, China.

ORCID-Profile: Hao Liu

Förderung

  • Adayi Xieeryazidan
  • National Natural Science Foundation of China

Zitieren

APA

Liu, H., & Xieeryazidan, A. (2023). Study of Gas Film Characteristics in Electrochemical Discharge Machining and Their Effects on Discharge Energy Distribution. Micromachines, 14(5), 1079. https://doi.org/10.3390/mi14051079

Vancouver

Liu H, Xieeryazidan A. Study of Gas Film Characteristics in Electrochemical Discharge Machining and Their Effects on Discharge Energy Distribution. Micromachines. 2023;14(5):1079. doi:10.3390/mi14051079

BibTeX
@article{Liu2023,
  author = {Liu, Hao and Xieeryazidan, Adayi},
  title = {Study of Gas Film Characteristics in Electrochemical Discharge Machining and Their Effects on Discharge Energy Distribution},
  journal = {Micromachines},
  year = {2023},
  volume = {14},
  number = {5},
  pages = {1079},
  doi = {10.3390/mi14051079}
}
Kostenlos starten →