EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of Heat Treatment on the Microstructure and Mechanical Properties of Ti–6Al–4V Alloy Produced by L-PBF and PA-DED

Svetlana Gatina, Andrey Stotskiy, Alfiz Gareev, Alexander Ryzhkin, Irina Semenova, Alexey Mamalat, Olga Klimova-Korsmik, Sergey Zherebtsov, Nariman Enikeev

Metals · 14.07.2026 · 16 (7) · 792

DOI: 10.3390/met16070792 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Metals, online erschienen am 14.07.2026. Verfasst von Svetlana Gatina und 8 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 44 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Russian Science Foundation.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The manufacturing of personalized implants from Ti–6Al–4V alloy using additive manufacturing technologies is a promising direction in modern medicine. However, components produced by these methods are characterized by a non-equilibrium microstructure, high residual stresses, and anisotropy of mechanical properties, which necessitates subsequent heat treatment. The aim of the present work was a systematic comparative study of the effect of three heat treatment regimes—stress relief annealing (600 °C, 3 h), subtransus annealing in the (α + β) region (950 °C, 1 h, furnace cooling), and solution treatment followed by aging (STA: 950 °C, 0.5 h, water quenching + aging at 675 °C, 3 h)—on the microstructure and mechanical properties of Ti–6Al–4V alloy manufactured by laser powder bed fusion (L-PBF) and plasma arc directed energy deposition (PA-DED). The microstructure was examined using scanning electron microscopy, transmission electron microscopy, and electron backscatter diffraction (EBSD). Tensile mechanical properties were determined in two directions: parallel and perpendicular to the build direction. Stress-relief annealing led to an increase in the ductility of the alloy without a noticeable decrease in strength and without significant changes in the microstructure. Subtransus annealing resulted in the formation of an equilibrium lamellar (α + β) structure, which provided a substantial increase in ductility with a moderate decrease in strength. Solution treatment and aging resulted in formation of a bimodal microstructure. Subtransus annealing (both alloys), STA (L-PBF) and stress relief annealing (PA-DED) provided properties comparable to those of wrought material. The obtained results form the basis for a scientifically informed selection of both the manufacturing route and the heat treatment regime for biomedical implants made of Ti–6Al–4V alloy.

Förderung

  • Russian Science Foundation

Zitieren

APA

Gatina, S., Stotskiy, A., Gareev, A., Ryzhkin, A., Semenova, I., Mamalat, A., Klimova-Korsmik, O., Zherebtsov, S., & Enikeev, N. (2026). Effect of Heat Treatment on the Microstructure and Mechanical Properties of Ti–6Al–4V Alloy Produced by L-PBF and PA-DED. Metals, 16(7), 792. https://doi.org/10.3390/met16070792

Vancouver

Gatina S, Stotskiy A, Gareev A, Ryzhkin A, Semenova I, Mamalat A, et al. Effect of Heat Treatment on the Microstructure and Mechanical Properties of Ti–6Al–4V Alloy Produced by L-PBF and PA-DED. Metals. 2026;16(7):792. doi:10.3390/met16070792

BibTeX
@article{Gatina2026,
  author = {Gatina, Svetlana and Stotskiy, Andrey and Gareev, Alfiz and Ryzhkin, Alexander and Semenova, Irina and Mamalat, Alexey and Klimova-Korsmik, Olga and Zherebtsov, Sergey and Enikeev, Nariman},
  title = {Effect of Heat Treatment on the Microstructure and Mechanical Properties of Ti–6Al–4V Alloy Produced by L-PBF and PA-DED},
  journal = {Metals},
  year = {2026},
  volume = {16},
  number = {7},
  pages = {792},
  doi = {10.3390/met16070792}
}
Kostenlos starten →