EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of Extrusion Ratio on Microstructure and Properties of Al-1.5Fe-0.4Cr Alloy Obtained by Continuous Rheo-Extrusion

Yunhe Ning, Li Yang, Minqiang Gao, Renguo Guan

Metals · 20.11.2024 · 14 (11) · 1310

DOI: 10.3390/met14111310 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Metals, online erschienen am 20.11.2024. Verfasst von Yunhe Ning und 3 weiteren Autor:innen. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 28 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Key Research and Development Program of China, National Natural Science Foundation of China, Dalian High-level Talents Innovation Support Program.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Due to the shortage of primary Al resources and significant consumption of Al resources, recycled Al has become a focus of attention. In the process of recycling Al, the Fe element is the most hazardous impurity element, and the coarse Fe-containing phases lead to a reduction in the mechanical properties of recycled Al. In this work, an Al alloy with 1.5 wt% Fe and 0.4 wt% Cr was viewed as a recycled Al, approximately. The continuous rheo-extrusion technique was used to refine the Fe-containing phases in the Al-1.5Fe-0.4Cr alloy, improving the mechanical properties of the alloy. The effect of the extrusion ratio on the microstructure and properties of the continuous rheo-extrusion was investigated. The results showed that, when the extrusion ratio was changed from 4 to 5, the percentage of low-angle grain boundaries in the alloy increased from 45.5% to 53.1%, the average orientation angle reduced from 23.9° to 23.3°, and the grain size decreased from 4.3 ± 0.2 μm to 2.6 ± 0.1 μm. As a result, the ultimate tensile strength, yield strength and elongation of the alloy, with an extrusion ratio of 5, were 161.5 ± 2.8 MPa, 112.3 MPa ± 2.6, and 36.9% ± 1.6%, respectively. Grain refinement and Fe-containing phase refinement were responsible for the improvement in the mechanical properties of the alloy.

Förderung

  • National Key Research and Development Program of China
  • National Natural Science Foundation of China
  • Dalian High-level Talents Innovation Support Program
  • Basic Research Program of Liaoning Provincial Department of Education

Zitieren

APA

Ning, Y., Yang, L., Gao, M., & Guan, R. (2024). Effect of Extrusion Ratio on Microstructure and Properties of Al-1.5Fe-0.4Cr Alloy Obtained by Continuous Rheo-Extrusion. Metals, 14(11), 1310. https://doi.org/10.3390/met14111310

Vancouver

Ning Y, Yang L, Gao M, Guan R. Effect of Extrusion Ratio on Microstructure and Properties of Al-1.5Fe-0.4Cr Alloy Obtained by Continuous Rheo-Extrusion. Metals. 2024;14(11):1310. doi:10.3390/met14111310

BibTeX
@article{Ning2024,
  author = {Ning, Yunhe and Yang, Li and Gao, Minqiang and Guan, Renguo},
  title = {Effect of Extrusion Ratio on Microstructure and Properties of Al-1.5Fe-0.4Cr Alloy Obtained by Continuous Rheo-Extrusion},
  journal = {Metals},
  year = {2024},
  volume = {14},
  number = {11},
  pages = {1310},
  doi = {10.3390/met14111310}
}
Kostenlos starten →