EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effects of TiAlN Coating Thickness on Machined Surface Roughness, Surface Residual Stresses, and Fatigue Life in Turning Inconel 718

Aisheng Jiang, Jinfu Zhao, Pengcheng Cui, Zhanqiang Liu, Bing Wang

Metals · 17.08.2024 · 14 (8) · 940

DOI: 10.3390/met14080940 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Metals, online erschienen am 17.08.2024. Verfasst von Aisheng Jiang und 4 weiteren Autor:innen. Die Arbeit wurde bisher 11-mal zitiert (Crossref) und nennt 42 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Postdoctoral Innovation Project of Shandong Province, Natural Science Foundation of Shandong Province.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The surface roughness and surface residual stresses are affected by the coating thickness of physical vapor deposition (PVD) TiAlN tools, which could alter the service performance of machined components. However, the relationships among the tool coating thickness, the machined surface roughness, the surface residual stress, and the fatigue life are still not sufficiently illustrated. In this research, PVD TiAlN coatings with several thicknesses of 1.6 μm, 2 μm, 2.5 μm, and 3 μm were deposited on carbide tools. Turning experiments using Inconel 718 were conducted with uncoated and various TiAlN tools under flood cooling conditions. The surface roughness could be improved with the selection of thin PVD TiAlN coating thicknesses of 1.6 μm and 2 μm compared to that of uncoated tools. The tensile residual stresses at the machined surface in the directions of cutting speed and feed rate linearly decreased by 148.67% and exponentially decreased by 92.24% when the TiAlN coating thickness was increased from 0 μm to 3 μm. The values of the low-cycle fatigue life of machined Inconel 718 linearly increased by 15.60% with the increase in TiAlN coating thickness from 0 μm to 3 μm, which was mainly due to the improvement of surface residual stresses. The results could provide guidance for the selection of suitable TiAlN coating thicknesses for wet machining Inconel 718 based on the part service conditions.

Förderung

  • National Natural Science Foundation of China
  • Postdoctoral Innovation Project of Shandong Province
  • Natural Science Foundation of Shandong Province
  • Shandong Provincial Key Research and Development Program (Major Scientific and Technological Innovation Project)
  • Taishan Scholar Foundation

Zitieren

APA

Jiang, A., Zhao, J., Cui, P., Liu, Z., & Wang, B. (2024). Effects of TiAlN Coating Thickness on Machined Surface Roughness, Surface Residual Stresses, and Fatigue Life in Turning Inconel 718. Metals, 14(8), 940. https://doi.org/10.3390/met14080940

Vancouver

Jiang A, Zhao J, Cui P, Liu Z, Wang B. Effects of TiAlN Coating Thickness on Machined Surface Roughness, Surface Residual Stresses, and Fatigue Life in Turning Inconel 718. Metals. 2024;14(8):940. doi:10.3390/met14080940

BibTeX
@article{Jiang2024,
  author = {Jiang, Aisheng and Zhao, Jinfu and Cui, Pengcheng and Liu, Zhanqiang and Wang, Bing},
  title = {Effects of TiAlN Coating Thickness on Machined Surface Roughness, Surface Residual Stresses, and Fatigue Life in Turning Inconel 718},
  journal = {Metals},
  year = {2024},
  volume = {14},
  number = {8},
  pages = {940},
  doi = {10.3390/met14080940}
}
Kostenlos starten →