EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Optimization of Dry Turning of Inconel 601 Alloy Based on Surface Roughness, Tool Wear, and Material Removal Rate

Goran Jovicic, Aleksandar Milosevic, Zeljko Kanovic, Mario Sokac, Goran Simunovic, Borislav Savkovic, Djordje Vukelic

Metals · 02.06.2023 · 13 (6) · 1068

DOI: 10.3390/met13061068 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Metals, online erschienen am 02.06.2023. Verfasst von Goran Jovicic und 6 weiteren Autor:innen. Die Arbeit wurde bisher 24-mal zitiert (Crossref) und nennt 40 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Science, Technological Development and Innovation of the Republic of Serbia, University of Slavonski Brod, Mechanical Engineering Faculty in Slavonski Brod, Republic of Croatia.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this work, the dry turning of Inconel 601 alloy in a dry environment with PVD-coated cutting inserts was studied. Turning was performed at various cutting speeds, feeds, insert shapes, corner radii, rake angles, and approach angles. After machining, arithmetic mean surface roughness (Ra) and flank wear (VB) were measured, and the material removal rate was also calculated (MRR). An analysis of variance (ANOVA) was performed to determine the effects of the turning input parameters. For the measured values, the turning process was modeled using an artificial neural network (ANN). Based on the obtained model, the process parameters were optimized using a genetic algorithm (GA). The objective function was to simultaneously minimize Ra and VB and maximize MRR. The accuracy of the model and the optimal values were further validated by confirmation experiments. The maximum percentage errors, which are less than 2%, indicate the possibility of practical implementation of the hybrid approach for modeling and optimization of dry turning of Inconel 601 alloy.

Förderung

  • Ministry of Science, Technological Development and Innovation of the Republic of Serbia
  • University of Slavonski Brod, Mechanical Engineering Faculty in Slavonski Brod, Republic of Croatia

Zitieren

APA

Jovicic, G., Milosevic, A., Kanovic, Z., Sokac, M., Simunovic, G., Savkovic, B., & Vukelic, D. (2023). Optimization of Dry Turning of Inconel 601 Alloy Based on Surface Roughness, Tool Wear, and Material Removal Rate. Metals, 13(6), 1068. https://doi.org/10.3390/met13061068

Vancouver

Jovicic G, Milosevic A, Kanovic Z, Sokac M, Simunovic G, Savkovic B, et al. Optimization of Dry Turning of Inconel 601 Alloy Based on Surface Roughness, Tool Wear, and Material Removal Rate. Metals. 2023;13(6):1068. doi:10.3390/met13061068

BibTeX
@article{Jovicic2023,
  author = {Jovicic, Goran and Milosevic, Aleksandar and Kanovic, Zeljko and Sokac, Mario and Simunovic, Goran and Savkovic, Borislav and Vukelic, Djordje},
  title = {Optimization of Dry Turning of Inconel 601 Alloy Based on Surface Roughness, Tool Wear, and Material Removal Rate},
  journal = {Metals},
  year = {2023},
  volume = {13},
  number = {6},
  pages = {1068},
  doi = {10.3390/met13061068}
}
Kostenlos starten →