EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Hot Forging Die Design Optimization Using FEM Analysis for Near-Net Forming of 18CrNiMo7-6 Steel Pinion Shaft

Nijenthan Rajendran, Charles Chemale Yurgel, Wojciech Z. Misiolek, Ricardo Alves de Sousa

Metals · 21.04.2023 · 13 (4) · 815

DOI: 10.3390/met13040815 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Metals, online erschienen am 21.04.2023. Verfasst von Nijenthan Rajendran und 3 weiteren Autor:innen. Die Arbeit wurde bisher 20-mal zitiert (Crossref) und nennt 25 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Loewy Institute at Lehigh University.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The objective of the presented work was to develop a new forging process for a pinion shaft as a component of a wind turbine. A study of near-net-shape forming using Deform 3D software was performed to reduce operational cost, time, and material scrap; enhance specific properties; increase productivity. Near-net forged products have good dimensional accuracy and continuous metal flow lines, which are characteristic of improved mechanical properties. To avoid the traditional trial-and-error experimental method, the process and tool design were accomplished with a careful and detailed numerical simulation approach. In the present work, the Finite Element Method was used to develop a process model for the existing hot forging process of the 18CrNiMo7-6 steel pinion shaft used in a wind turbine. The developed numerical process model was validated via experiment including a comparison of the metal flow lines from the FEM model with the metallography results of the forged part. Two new die designs were proposed, and the simulation results were compared to the actual process to achieve improved geometry. The results for the new geometries showed improvements in terms of the die cavity filling for the new proposed dies and better results in grain flow orientation. Compared to the initial non-optimized die, the new designs improved the mechanical properties and savings associated with the lower volume of required raw material and fewer finishing operations. Considering the applied stresses and wear in the new near-net shape, the die geometry shall be updated to accommodate more severe solicitations. Naturally, all the improvements carried out are dependent on other factors such as the conditions of the equipment, operator skills, lubrication, and other variables. A surface heat treatment is also suggested for stress relief as a reliability improvement.

Förderung

  • Loewy Institute at Lehigh University

Zitieren

APA

Rajendran, N., Yurgel, C. C., Misiolek, W. Z., & Sousa, R. A. D. (2023). Hot Forging Die Design Optimization Using FEM Analysis for Near-Net Forming of 18CrNiMo7-6 Steel Pinion Shaft. Metals, 13(4), 815. https://doi.org/10.3390/met13040815

Vancouver

Rajendran N, Yurgel CC, Misiolek WZ, Sousa RAD. Hot Forging Die Design Optimization Using FEM Analysis for Near-Net Forming of 18CrNiMo7-6 Steel Pinion Shaft. Metals. 2023;13(4):815. doi:10.3390/met13040815

BibTeX
@article{Rajendran2023,
  author = {Rajendran, Nijenthan and Yurgel, Charles Chemale and Misiolek, Wojciech Z. and Sousa, Ricardo Alves de},
  title = {Hot Forging Die Design Optimization Using FEM Analysis for Near-Net Forming of 18CrNiMo7-6 Steel Pinion Shaft},
  journal = {Metals},
  year = {2023},
  volume = {13},
  number = {4},
  pages = {815},
  doi = {10.3390/met13040815}
}
Kostenlos starten →