Solid Oxide Fuel Cells with Magnetron Sputtered Single-Layer SDC and Multilayer SDC/YSZ/SDC Electrolytes
Membranes · 05.06.2023 · 13 (6) · 585
DOI: 10.3390/membranes13060585 ↗Kurz gefasst
Fachartikel in der Zeitschrift Membranes, online erschienen am 05.06.2023. Verfasst von Andrey Solovyev und 2 weiteren Autor:innen. Beteiligte Einrichtung: Institute of High Current Electronics SB RAS, 634055 Tomsk, Russia. Die Arbeit wurde bisher 22-mal zitiert (Crossref) und nennt 50 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: the Ministry of Science and Higher Education of the Russian Federation.
Abstract (Originalsprache)
Samarium-doped ceria (SDC) is considered as an alternative electrolyte material for intermediate-temperature solid oxide fuel cells (IT-SOFCs) because its conductivity is higher than that of commonly used yttria-stabilized zirconia (YSZ). The paper compares the properties of anode-supported SOFCs with magnetron sputtered single-layer SDC and multilayer SDC/YSZ/SDC thin-film electrolyte, with the YSZ blocking layer 0.5, 1, and 1.5 μm thick. The thickness of the upper and lower SDC layers of the multilayer electrolyte are constant and amount to 3 and 1 μm, respectively. The thickness of single-layer SDC electrolyte is 5.5 μm. The SOFC performance is studied by measuring current–voltage characteristics and impedance spectra in the range of 500–800 °C. X-ray diffraction and scanning electron microscopy are used to investigate the structure of the deposited electrolyte and other fuel cell layers. SOFCs with the single-layer SDC electrolyte show the best performance at 650 °C. At this temperature, open circuit voltage and maximum power density are 0.8 V and 651 mW/cm2, respectively. The formation of the SDC electrolyte with the YSZ blocking layer improves the open circuit voltage up to 1.1 V and increases the maximum power density at the temperatures over 600 °C. It is shown that the optimal thickness of the YSZ blocking layer is 1 µm. The fuel cell with the multilayer SDC/YSZ/SDC electrolyte, with the layer thicknesses of 3/1/1 µm, has the maximum power density of 2263 and 1132 mW/cm2 at 800 and 650 °C, respectively.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Institute of High Current Electronics SB RAS, 634055 Tomsk, Russia.
- Department of Physics, National Research Tomsk State University, 634050 Tomsk, Russia.
- School of Advanced Manufacturing Technologies, National Research Tomsk Polytechnic University, 634050 Tomsk, Russia.
ORCID-Profile: Andrey Solovyev, Anna Shipilova
Förderung
- the Ministry of Science and Higher Education of the Russian Federation
Zitieren
APA
Solovyev, A., Shipilova, A., & Smolyanskiy, E. (2023). Solid Oxide Fuel Cells with Magnetron Sputtered Single-Layer SDC and Multilayer SDC/YSZ/SDC Electrolytes. Membranes, 13(6), 585. https://doi.org/10.3390/membranes13060585
Vancouver
Solovyev A, Shipilova A, Smolyanskiy E. Solid Oxide Fuel Cells with Magnetron Sputtered Single-Layer SDC and Multilayer SDC/YSZ/SDC Electrolytes. Membranes. 2023;13(6):585. doi:10.3390/membranes13060585
BibTeX
@article{Solovyev2023,
author = {Solovyev, Andrey and Shipilova, Anna and Smolyanskiy, Egor},
title = {Solid Oxide Fuel Cells with Magnetron Sputtered Single-Layer SDC and Multilayer SDC/YSZ/SDC Electrolytes},
journal = {Membranes},
year = {2023},
volume = {13},
number = {6},
pages = {585},
doi = {10.3390/membranes13060585}
}
EUVIMED