Microstructure Evolution and Strength–Toughness Trade-Off in 1Cr12Ni2WMoVNb Martensitic Stainless Steel During Tempering
Materials · 06.08.2026 · 19 (15) · 3350
DOI: 10.3390/ma19153350 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 06.08.2026. Verfasst von Jiashun Gao und 5 weiteren Autor:innen. Beteiligte Einrichtung: School of Marine Mechatronics, Xiamen Ocean Vocational College, Xiamen 361000, China. Die Arbeit nennt 53 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Engineering Research Center of Anti-Fatigue Manufacturing for Marine Equipment of Fujian Province, China, Science and Technology Project of Fujian Province, China.
Abstract (Originalsprache)
The influence of tempering temperature on the microstructure evolution and mechanical properties of 1Cr12Ni2WMoVNb martensitic stainless steel was systematically investigated in the range of 200–650 °C. Microhardness, tensile strength, and impact toughness were evaluated, combined with analyses using confocal laser scanning microscopy (CLSM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy-dispersive spectroscopy (EDS), and phase characterization techniques. The results show that hardness and tensile strength initially decrease, then increase to a peak at approximately 550 °C due to secondary hardening, and finally decline significantly. In contrast, impact toughness exhibits an inverse trend, revealing a clear strength–toughness trade-off. Microstructural analysis indicates that this behavior is governed by the competition among multiple strengthening mechanisms. At intermediate temperatures, the precipitation of fine and dispersed M23C6 carbides leads to strong dislocation pinning and pronounced precipitation strengthening, resulting in peak strength but reduced plastic deformation capability. At higher temperatures, carbide coarsening and dislocation recovery weaken strengthening while restoring plasticity, thereby improving toughness. These findings clarify the temperature-dependent competition among strengthening mechanisms governing the strength–toughness evolution during tempering.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- School of Marine Mechatronics, Xiamen Ocean Vocational College, Xiamen 361000, China.
- Engineering Research Center of Anti-Fatigue Manufacturing for Marine Equipment of Fujian Province, Xiamen 361000, China.
- School of Marine Equipment and Mechanical Engineering, Jimei University, Xiamen 361000, China.
- Chengyi College, Jimei University, Xiamen 361000, China.
- Sichuan Huadian Gongxian Power Generation Co., Ltd., Yibin 644500, China.
Förderung
- National Natural Science Foundation of China
- Engineering Research Center of Anti-Fatigue Manufacturing for Marine Equipment of Fujian Province, China
- Science and Technology Project of Fujian Province, China
- Research Project on Manufacturing Technology for Long-Life Fatigue-Resistant Connecting Pins of Xiamen, Fujian, China
- Research Project on Failure Mechanisms and Anti-Fatigue Manufacturing Technologies of Steam Turbine Blades of Xiamen, Fujian, China
- Engineering Research Center of Anti-Fatigue Manufacturing for Marine Equipment of Fujian Province
- Science and Technology Project of Fujian Province
- Research Project on Manufacturing Technology for Long-Life Fatigue-Resistant Connecting Pins
Zitieren
APA
Gao, J., Liu, L., Xu, Z., Zhu, J., Hu, Z., & Lin, H. (2026). Microstructure Evolution and Strength–Toughness Trade-Off in 1Cr12Ni2WMoVNb Martensitic Stainless Steel During Tempering. Materials, 19(15), 3350. https://doi.org/10.3390/ma19153350
Vancouver
Gao J, Liu L, Xu Z, Zhu J, Hu Z, Lin H. Microstructure Evolution and Strength–Toughness Trade-Off in 1Cr12Ni2WMoVNb Martensitic Stainless Steel During Tempering. Materials. 2026;19(15):3350. doi:10.3390/ma19153350
BibTeX
@article{Gao2026,
author = {Gao, Jiashun and Liu, Liehua and Xu, Zhilong and Zhu, Jiang and Hu, Zhijie and Lin, Hongxin},
title = {Microstructure Evolution and Strength–Toughness Trade-Off in 1Cr12Ni2WMoVNb Martensitic Stainless Steel During Tempering},
journal = {Materials},
year = {2026},
volume = {19},
number = {15},
pages = {3350},
doi = {10.3390/ma19153350}
}
EUVIMED