EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Wear Behavior of Austenitic Stainless Steel 316L Plates Fabricated by Wire Arc Additive Manufacturing

Hussam H Noor iD, Mohammed T Alamoudi iD, Khalid Alqosaibi, Saleh Alzughaibi iD, Youssef Alammari iD, Abdulrahman Alrumayh iD, Faisal J Alzahrani iD

Materials · 30.07.2026 · 19 (15) · 3236

DOI: 10.3390/ma19153236 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 30.07.2026. Verfasst von Hussam H Noor und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, College of Engineering, Taibah University, Medina 42353, Saudi Arabia. Die Arbeit nennt 50 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Deanship of Graduate Studies and Scientific Research at Qassim University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Additive manufacturing (AM) of stainless steel has been gaining industry attention in recent years due to the need to manufacture complex steel components. Many sectors stand to benefit from the design flexibility, customization, and rapid production capabilities of AM. However, the industry’s adoption of this technology remains limited due to concerns about the mechanical integrity and reliability of AM products. This experimental study examines the wear and tribological behavior of Wire Arc Additive Manufactured (WAAM) austenitic stainless steel 316L. Pin-on-disk tests were conducted using a 5 mm tungsten carbide ball under dry sliding conditions at normal loads of 1.5 and 2.5 N and sliding speeds between 0.03 and 0.229 m/s. The results showed that the coefficient of friction remained relatively stable at approximately 0.6, while wear volume generally decreased with increasing sliding speed. Lower normal loads resulted in lower wear volume, whereas the wear factor showed only limited sensitivity to the applied load. Optical microscopy revealed a ferrite–austenite microstructure with residual δ-ferrite that contributes to the observed wear behavior. These findings demonstrate the suitability of WAAM-produced 316L stainless steel for tribological applications requiring stable frictional performance.

Schlagwörter

Stichwörter der Autor:innen

316LWAAMaustenitic stainless steelmicrostructurepin-on-disktribologywear

Autor:innen und Institutionen

  • Department of Mechanical Engineering, College of Engineering, Taibah University, Medina 42353, Saudi Arabia.
  • Advanced Materials Technologies Institute, Energy and Industry Sector, King Abdulaziz City for Science and Technology, Riyadh 11442, Saudi Arabia.
  • Department of Mechanical Engineering, College of Engineering, King Saud University, Riyadh 12372, Saudi Arabia.
  • Department of Mechanical Engineering, College of Engineering, Qassim University, Buraidah 51452, Saudi Arabia.
  • Department of Mechanical Engineering, Faculty of Engineering-Rabigh, King Abdulaziz University, Jeddah 21589, Saudi Arabia.

ORCID-Profile: Hussam H Noor, Mohammed T Alamoudi, Saleh Alzughaibi, Youssef Alammari, Abdulrahman Alrumayh, Faisal J Alzahrani

Förderung

  • Deanship of Graduate Studies and Scientific Research at Qassim University

Zitieren

APA

Noor, H. H., Alamoudi, M. T., Alqosaibi, K., Alzughaibi, S., Alammari, Y., Alrumayh, A., & Alzahrani, F. J. (2026). Wear Behavior of Austenitic Stainless Steel 316L Plates Fabricated by Wire Arc Additive Manufacturing. Materials, 19(15), 3236. https://doi.org/10.3390/ma19153236

Vancouver

Noor HH, Alamoudi MT, Alqosaibi K, Alzughaibi S, Alammari Y, Alrumayh A, et al. Wear Behavior of Austenitic Stainless Steel 316L Plates Fabricated by Wire Arc Additive Manufacturing. Materials. 2026;19(15):3236. doi:10.3390/ma19153236

BibTeX
@article{Noor2026,
  author = {Noor, Hussam H and Alamoudi, Mohammed T and Alqosaibi, Khalid and Alzughaibi, Saleh and Alammari, Youssef and Alrumayh, Abdulrahman and Alzahrani, Faisal J},
  title = {Wear Behavior of Austenitic Stainless Steel 316L Plates Fabricated by Wire Arc Additive Manufacturing},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {15},
  pages = {3236},
  doi = {10.3390/ma19153236}
}
Kostenlos starten →