EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Wear Behavior of Austenitic Stainless Steel 308L Fabricated by Wire Arc Additive Manufacturing

Saleh Alzughaibi iD, Youssef Alammari iD, Abdulrahman Alrumayh iD, Mohammed T Alamoudi iD, Faisal J Alzahrani iD, Hussam H Noor iD, Khalid Alqosaibi

Materials · 24.05.2026 · 19 (11) · 2207

DOI: 10.3390/ma19112207 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Materials, online erschienen am 24.05.2026. Verfasst von Saleh Alzughaibi und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, College of Engineering, Qassim University, Buraidah 51452, Saudi Arabia. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 26 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: King Saud University-Project.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Wire Arc Additive Manufacturing (WAAM) has emerged as a cost-effective and high-deposition-rate technique for fabricating large-scale metallic components; however, the complex thermal history inherent to the process leads to heterogeneous microstructures that can significantly influence tribological performance. In this study, the dry sliding wear behavior of WAAM-fabricated austenitic stainless steel 308L (SS308L) was systematically investigated using a pin-on-disk configuration. The influence of applied normal load (1.5–15 N) and sliding speed (0.03–0.229 m/s) on wear volume, specific wear rate, coefficient of friction (COF), and tangential force was evaluated. Optical microstructural observations indicated features consistent with a ferritic–austenitic solidification structure, including regions resembling polygonal ferrite, Widmanstätten ferrite, and austenitic dendritic morphologies. Wear results showed that wear volume and cross-sectional area increased monotonically with increasing load, while the effect of sliding speed was comparatively less significant. The specific wear rate remained on the order of 10−4 mm3/N·m with minor variations across test conditions. The COF decreased with increasing load up to 10 N, followed by a speed-dependent response at higher loads. The findings demonstrate that load is the dominant factor governing wear behavior in WAAM SS308L, while microstructural heterogeneity may contribute to frictional stability and wear resistance. This study provides valuable insight into the structure–tribology relationship of WAAM stainless steels and supports the optimization of process parameters for wear-critical applications.

Schlagwörter

Stichwörter der Autor:innen

308Wire Arc Additive Manufacturing (WAAM)austenitic stainless steelmicrostructurepin-on-disktribologywear

Autor:innen und Institutionen

  • Department of Mechanical Engineering, College of Engineering, Qassim University, Buraidah 51452, Saudi Arabia.
  • Advanced Materials Technologies Institute, Energy and Industry Sector, King Abdulaziz City for Science and Technology, Riyadh 11442, Saudi Arabia.
  • Department of Mechanical Engineering, College of Engineering-Rabigh, King Abdulaziz University, Jeddah 21589, Saudi Arabia.
  • Department of Mechanical Engineering, College of Engineering, Taibah University, Medina 42353, Saudi Arabia.
  • Department of Mechanical Engineering, College of Engineering, King Saud University, Riyadh 12372, Saudi Arabia.

ORCID-Profile: Saleh Alzughaibi, Youssef Alammari, Abdulrahman Alrumayh, Mohammed T Alamoudi, Faisal J Alzahrani, Hussam H Noor

Förderung

  • King Saud University-Project

Zitieren

APA

Alzughaibi, S., Alammari, Y., Alrumayh, A., Alamoudi, M. T., Alzahrani, F. J., Noor, H. H., & Alqosaibi, K. (2026). Wear Behavior of Austenitic Stainless Steel 308L Fabricated by Wire Arc Additive Manufacturing. Materials, 19(11), 2207. https://doi.org/10.3390/ma19112207

Vancouver

Alzughaibi S, Alammari Y, Alrumayh A, Alamoudi MT, Alzahrani FJ, Noor HH, et al. Wear Behavior of Austenitic Stainless Steel 308L Fabricated by Wire Arc Additive Manufacturing. Materials. 2026;19(11):2207. doi:10.3390/ma19112207

BibTeX
@article{Alzughaibi2026,
  author = {Alzughaibi, Saleh and Alammari, Youssef and Alrumayh, Abdulrahman and Alamoudi, Mohammed T and Alzahrani, Faisal J and Noor, Hussam H and Alqosaibi, Khalid},
  title = {Wear Behavior of Austenitic Stainless Steel 308L Fabricated by Wire Arc Additive Manufacturing},
  journal = {Materials},
  year = {2026},
  volume = {19},
  number = {11},
  pages = {2207},
  doi = {10.3390/ma19112207}
}
Kostenlos starten →